1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT
| *a | 5 m (16.4 ft.) |
| *b | 6 m (19.7 ft.) |
| *c | 4 m (13.1 ft.) |
| *d | 2 m (6.56 ft.) |
| *e | 3 m (9.84 ft.) |
| *f | 1.5 m (4.92 ft.) |
| *g | 2.5 m (8.20 ft.) |
|
Do not place any metal objects in this area |
|
Do not place metal objects with a height of more than 50 mm (1.97 in.) in this area |
Park the vehicle on a level surface where the area in front of the vehicle shown in the illustration is free of metal objects.
Metal objects with a height of 50 mm (1.97 in.) or less placed within the area shown in the illustration will not affect the adjustment.
Check the levelness of the ground.
| *a | 3 m (9.84 ft.) |
|
Levelness Check Point |
Check the levelness of the ground at the 3 points shown in the illustration.
Place the level on each levelness check point and check that the air bubble of the level is centered.
Adjust the tire inflation pressure to the specified pressure.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Clean the front emblem or millimeter wave radar sensor assembly.
Visually inspect the front of the vehicle.
Confirm that there is no damage or deformation.
Visually inspect the front bumper assembly, radiator grill and stays.
Confirm that there is no damage or deformation.
2. MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY
| *a | SST (reflector) |
Adjust SST (reflector) height.
Adjust SST (reflector) so that the center of SST (reflector) is the same height as the millimeter wave radar sensor.
Make sure to align the center of SST (reflector) with the millimeter wave radar sensor (the center of the emblem).
766.5 mm (2.51 ft.)
Hang a weight with a pointed tip from the center of the rear emblem, and mark the rear center point of the vehicle (point A) on the ground.
| *a | String | *b | Weight |
| *c | Center | - | - |
Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.
Hang a weight with a pointed tip from the center of the front emblem, and mark the front center point of the vehicle (point B) on the ground.
| *a | String | *b | Weight |
| *c | Center | - | - |
Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.
Using tape and a string, create a line that connects point B to point A and extends at least 3000 mm (9.84 ft.) beyond the front center point of the vehicle.
| *a | String | *b | Tape |
| *c | 3000 mm (9.84 ft.) | - | - |
Make sure the string is taut when securing it with tape.
Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.
Mark point C (SST (reflector) placement position) at a position 3000 mm (9.84 ft.) from point B.
Place SST (reflector) at point C.
Front Beam Axis Adjustment:
Close all of the doors.
Ensure that nobody enters the adjustment area during the adjustment.
Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).
Do not turn off the GTS or ignition switch.
If the vehicle moves or is shaken during beam axis adjustment such as during strong winds or a door is opened or closed, perform the adjustment again.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Beam Axis Adjustment.
| Tester Display |
|---|
| Front Beam Axis Adjustment |
Press "Next".
Perform the adjustment according to the display on the GTS.
If an error code is displayed, perform troubleshooting according to the following table, then perform the adjustment again.
Press "Exit" to finish front beam axis adjustment.
Front Beam Axis Misalignment Reading:
Close all of the doors.
Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).
Ensure that nobody enters the adjustment area during the adjustment.
Do not turn off the GTS or ignition switch.
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Beam Axis Misalignment Reading.
| Tester Display |
|---|
| Front Beam Axis Misalignment Reading |
Press "Next".
Perform the adjustment according to the display on the GTS.
| Vertical | -0.5 to 0.5 deg. |
| Horizontal | -0.5 to 0.5 deg. |
If the result is not as specified, perform beam axis adjustment again.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
After beam axis adjustment completes, clear the following system vehicle control history entries.
Clear vehicle control history (Dynamic radar cruise control system).
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Lane tracing assist system).
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE TRACING ASSIST SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Road sign assist system).
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Front radar sensor system).
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Pre-collision system).
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Automatic high beam system).
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HIGH BEAM SYSTEM>VEHICLE CONTROL HISTORY