Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297889 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. The ECM uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the ECM determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the dynamic radar cruise control system is operating, the ECM detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

ECM


Cruise Control

WIRING DIAGRAM

C367135E23
1.385,1.229 2,1.427 0.615,0.198 10 false STOP 1.188,1.729 2.25,2.021 1.063,0.292 10 false ECU-IG2 NO. 3 3.354,2.448 4.115,2.646 0.76,0.198 10 false A91 3.344,2.594 4.438,2.979 1.094,0.385 10 false Stop Light Switch Assembly 3.438,2.083 4.198,2.281 0.76,0.198 10 false GND 3.448,1.573 4.208,1.771 0.76,0.198 10 false B 3.448,1.073 4.208,1.271 0.76,0.198 10 false B 3.24,0.969 3.49,1.146 0.25,0.177 10 false 7 3.24,1.469 3.49,1.688 0.25,0.219 10 false 6 3.25,1.969 3.5,2.188 0.25,0.219 10 false 2 3.552,3.51 4.313,3.708 0.76,0.198 10 false STP 3.563,5 4.323,5.198 0.76,0.198 10 false STP 3.979,5.198 4.229,5.396 0.25,0.198 10 false *2 3.958,4.99 4.417,5.188 0.458,0.198 10 false F18 4.344,4.99 4.802,5.188 0.458,0.198 10 false F19 4.333,5.198 4.583,5.396 0.25,0.198 10 false *1 2.969,5.385 4.094,5.792 1.125,0.406 10 false Shift Lock Control Unit Assembly 5.271,4 6.813,4.406 1.542,0.406 10 false Certification ECU (Smart Key ECU Assembly)*1 5.271,3.844 5.729,4.042 0.458,0.198 10 false M67 5.604,3.5 6.365,3.698 0.76,0.198 10 false STP1 3.938,3.417 4.396,3.615 0.458,0.198 10 false 42 5.344,3.417 5.802,3.615 0.458,0.198 10 false 25 5.927,2.448 6.385,2.646 0.458,0.198 10 false A38 5.917,2.604 6.375,2.802 0.458,0.198 10 false ECM 4.021,4.76 4.271,4.958 0.25,0.198 10 false 8 4.375,4.76 4.625,4.958 0.25,0.198 10 false 4 5.281,1.646 5.74,1.844 0.458,0.198 10 false 10 5.365,0.854 5.583,1.042 0.219,0.188 10 false 9 4.198,0.844 4.417,1.031 0.219,0.188 10 false 3 4.198,1.646 4.417,1.833 0.219,0.188 10 false 5 3.979,1.74 4.188,1.938 0.208,0.198 10 false L 3.99,0.958 4.198,1.156 0.208,0.198 10 false L 5.531,0.854 5.927,1.052 0.396,0.198 10 false STP 5.531,1.635 5.927,1.833 0.396,0.198 10 false ST1- 0.219,5.563 2.573,5.854 2.354,0.292 10 false *1: w/ Entry and Start System 0.219,5.979 2.573,6.271 2.354,0.292 10 false *2: w/o Entry and Start System 2.875,4.021 4.406,4.448 1.531,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 2.885,3.875 3.646,4.073 0.76,0.198 10 false A42

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the A91 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A91-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-7 (B) - Body ground Always 11 to 14 V
A91-6 (B) - Body ground Ignition switch ON 11 to 14 V
A91-6 (B) - Body ground Ignition switch off Below 1 V



d.

Connect the A91 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A38 ECM connectors.


b.

Disconnect the A91 stop light switch assembly connector.


c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the M67 certification ECU connector.*

*: w/ Entry and Start System



e.

Disconnect the F18*1 or F19*2 Shift Lock Control Unit Assembly connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-10 (ST1-) - A91-5 (L) Always Below 1 Ω
A38-9 (STP) - A91-3 (L) Always Below 1 Ω
A38-10 (ST1-) or A91-5 (L) - Body ground Always 10 kΩ or higher
A38-9 (STP) or A91-3 (L) - Body ground Always 10 kΩ or higher



g.

Connect the F18*1 or F19*2 Shift Lock Control Unit Assembly connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



h.

Connect the M67 certification ECU connector.*

*: w/ Entry and Start System



i.

Connect the A42 skid control ECU (brake actuator assembly) connector.


j.

Connect the A91 stop light switch assembly connector.


k.

Connect the A38 ECM connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR