| Pre-Collision System Malfunction Visit Your Dealer
|
X2000
|
Yaw Rate Sensor Malfunction
|
The forward recognition camera received a yaw rate sensor (airbag sensor assembly) malfunction signal from the skid control ECU (brake actuator assembly).
|
Perform troubleshooting for the vehicle stability control system.
Click here( )
|
| Pre-Collision System Malfunction Visit Your Dealer
|
X2004
|
Speed Sensor Malfunction
|
The forward recognition camera received a vehicle speed sensor malfunction signal from the skid control ECU (brake actuator assembly).
|
Perform troubleshooting for the vehicle stability control system.
Click here( )
|
| Pre-Collision System Malfunction Visit Your Dealer
|
X2014
|
Front Recognition Camera Optical Axis Not Adjusted
|
Forward recognition camera optical axis adjustment has not been performed.
|
- HINT:
-
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
-
One Time Recognition: Click here( )
-
Sequential Recognition: Click here( )
-
Driving Adjustment: Click here( )
|
| Front Camera Low Visibility Unavailable See Owner's Manual
|
X2015
|
Front Recognition Camera Dirt
|
System operation was temporarily suspended due to the forward recognition camera not being able to detect objects.
|
Check if any of the following conditions are met:
·
Non-Toyota genuine front wiper blades are installed
·
The front wiper rubbers are worn
·
A sticker, accessory or other object is obstructing the forward recognition camera
·
There is snow, frost, dirt, dust or oil on the windshield glass, or the windshield glass is fogged up
·
The windshield glass is chipped or cracked
·
Non-Toyota genuine windshield glass is installed
·
Confirm the vehicle was not driven in bad weather (If temporary conditions that affected the camera such as darkness, backlighting, fog, etc. have improved, the displayed warning is cleared).
Factor:
The area in front of the forward recognition camera is dirty or obstructed by foreign matter.
|
| Front Camera Out of Temperature Range Unavailable Wait until Normal Temperature
|
X2016
|
Front Recognition Camera Outside Guaranteed Operating Temperature
|
System operation was temporarily suspended due to the forward recognition camera being excessively hot or cold.
|
1.
Using the GTS, check the following items for the front recognition camera in the Data List.
( )
-
Front Recognition Camera Low Temperature
-
Front Recognition Camera High Temperature 1
2.
If the display value for the Data List check items are displayed as "High Temperature" or "Low Temperature", perform the procedures listed in the diagnostic notes.
( )
Cause:
The forward recognition camera is in one of the following conditions
-
When the ambient temperature is approximately -30°C (-22°F) or less, such as when the vehicle is left alone in an extremely cold environment
-
When the ambient temperature is approximately 80°C (176°F) or higher, such as when the vehicle is left alone in an extremely an extremely hot environment
|
| Front Camera Unavailable See Owner's Manual
|
X2017
|
Front Recognition Camera Outside Guaranteed Operating Voltage
|
System operation was temporarily suspended due to forward recognition camera power source voltage being excessively high or low.
|
Check the power source voltage of the forward recognition camera (terminal IGB). Refer to ( )for the terminal inspection and standard voltage.
If the power source voltage is within the specified range and "Front Camera Unavailable See Owner's Manual" is displayed in the multi-information display, the forward recognition camera may be malfunctioning.
Cause:
The forward recognition camera is in one of the following conditions
-
When the input voltage is approximately 9 V or less, immediately after starting the engine
-
When the input voltage is approximately 16 V or higher, immediately after starting the engine
|
| -
|
X204A
|
Acceleration Sensor Malfunction
|
The forward recognition camera received an acceleration sensor malfunction signal from the skid control ECU (brake actuator assembly).
|
Perform troubleshooting for the vehicle stability control system.
Click here( )
|