IGNITION SWITCH EXPRESSIONS
The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section.
| Expression | Ignition Switch (Position) | Engine Switch (Condition) |
|---|---|---|
| Ignition Switch off | LOCK | Off |
| Ignition Switch ON | ON | On (IG) |
| Ignition Switch ACC | ACC | On (ACC) |
| Engine Start | START | Start |
PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL
If the battery has been discharged and charged or the cable has been disconnected and reconnected to the negative (-) battery terminal, perform Steering Sensor Zero Point Calibration.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>INITIALIZATION
HANDLING PRECAUTIONS FOR SRS AIRBAG SYSTEM
This vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read Precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
TROUBLESHOOTING PRECAUTIONS
If a malfunction related to terminal contact or part installation occurs, removal and reinstallation of the suspected part may return the system to normal. However, this normal condition may only be temporary.
When determining the malfunctioning area, before disconnecting connectors or removing/installing parts, check for DTCs and note the vehicle condition and operations that were performed when the malfunction occurred (stored DTCs, etc.).
Be sure to check for DTCs related to other systems. The lane tracing assist system may be influenced by malfunctions in other systems.
HANDLING PRECAUTIONS
When removing or installing any ECUs or sensors, make sure that the ignition switch is off unless otherwise specified in the inspection procedure.
After removing and installing any ECUs or sensors, make sure to check for DTCs and confirm that no DTCs are output.
REPLACEMENT PRECAUTIONS
Millimeter Wave Radar Sensor Assembly:
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.
When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT
Forward Recognition Camera:
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT
When replacing the forward recognition camera, do not damage the camera lens or allow it to become contaminated with foreign matter.
Do not reuse a forward recognition camera that has been dropped or subjected to a strong impact.
Windshield Glass:
When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket or the lane tracing assist system may not operate properly due to a difference in the transmissivity or black ceramic border.
Do not attach stickers, including transparent stickers, or other items to the windshield glass near the forward recognition camera.
Steering Wheel Assembly:
When replacing the steering wheel assembly of a vehicle with a lane tracing assist system, make sure to use a Toyota genuine steering wheel assembly with a lane tracing assist system.