Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Power Steering (EPS)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Power Steering (EPS)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Power Steering (EPS)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Power steering ECU assembly branch line or connector

·

Power source circuit of power steering ECU assembly

·

Power steering ECU assembly ground circuit

·

Power steering ECU assembly



WIRING DIAGRAM

for LHD


C366178E16
1.635,0.521 1.792,0.719 0.156,0.198 10 false 6 1.615,1.063 1.865,1.313 0.25,0.25 10 false 17 0.177,1.552 0.677,1.719 0.5,0.167 10 false F123 0.167,1.719 2.167,1.969 2,0.25 10 false No. 4 CAN Junction Connector 1.854,2.208 3.271,2.458 1.417,0.25 10 false from IG1-NO. 1 Relay 4.229,2.385 4.896,2.552 0.667,0.167 10 false EPS-IG1 5.521,0.458 5.677,0.656 0.156,0.198 10 false 7 5.458,0.625 5.781,0.792 0.323,0.167 10 false F23 5.448,1.156 5.771,1.323 0.323,0.167 10 false F23 5.458,2.24 5.781,2.406 0.323,0.167 10 false F23 5.521,0.99 5.677,1.188 0.156,0.198 10 false 8 5.521,2.042 5.677,2.24 0.156,0.198 10 false 1 5.521,2.583 5.677,2.781 0.156,0.198 10 false 2 5.458,2.771 5.781,2.938 0.323,0.167 10 false F68 5.792,0.646 6.458,0.813 0.667,0.167 10 false CANH 5.781,1.177 6.448,1.344 0.667,0.167 10 false CANL 5.792,2.25 6.458,2.417 0.667,0.167 10 false IG 5.792,2.781 6.458,2.948 0.667,0.167 10 false PGND 5.604,3.208 6.969,3.583 1.365,0.375 10 false Power Steering ECU with Motor Assembly


for RHD



C366178E17
1.635,0.521 1.792,0.719 0.156,0.198 10 false 3 1.615,1.063 1.865,1.313 0.25,0.25 10 false 14 0.177,1.552 0.677,1.719 0.5,0.167 10 false F115 0.167,1.719 2.167,1.969 2,0.25 10 false No. 4 CAN Junction Connector 1.854,2.208 3.271,2.458 1.417,0.25 10 false from IG1-NO. 1 Relay 4.229,2.385 4.896,2.552 0.667,0.167 10 false EPS-IG1 5.521,0.458 5.677,0.656 0.156,0.198 10 false 7 5.458,0.625 5.781,0.792 0.323,0.167 10 false F23 5.448,1.156 5.771,1.323 0.323,0.167 10 false F23 5.458,2.24 5.781,2.406 0.323,0.167 10 false F23 5.521,0.99 5.677,1.188 0.156,0.198 10 false 8 5.521,2.042 5.677,2.24 0.156,0.198 10 false 1 5.521,2.583 5.677,2.781 0.156,0.198 10 false 2 5.458,2.771 5.781,2.938 0.323,0.167 10 false F68 5.792,0.646 6.458,0.813 0.667,0.167 10 false CANH 5.781,1.177 6.448,1.344 0.667,0.167 10 false CANL 5.792,2.25 6.458,2.417 0.667,0.167 10 false IG 5.792,2.781 6.458,2.948 0.667,0.167 10 false PGND 5.604,3.208 6.969,3.583 1.365,0.375 10 false Power Steering ECU with Motor Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (POWER STEERING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the power steering ECU assembly connector.


c.
C328898C20
1.458,0.5 1.958,0.75 0.5,0.25 1.417,2.667 1.781,1.885 true 2.333,2.667 2,1.885 true 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 1.594,0.552 1.906,0.75 0.313,0.198 10 false F23 1.24,2.708 1.854,2.906 0.615,0.198 10 false CANH 2.156,2.708 2.771,2.906 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F23-7 (CANH) - F23-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (POWER STEERING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the power steering ECU assembly connector.


b.
C328899C07
1.469,0.333 1.969,0.583 0.5,0.25 1.469,2.167 1.969,2.417 0.5,0.25 2.5,1 2.042,1.302 true 1.406,3.188 0.948,3.49 true 0.177,0.146 0.49,0.302 0.313,0.156 10 false *a 1.604,0.365 2.063,0.563 0.458,0.198 10 false F68 1.615,2.198 2.073,2.396 0.458,0.198 10 false F23 2.563,0.938 3.177,1.135 0.615,0.198 10 false PGND 0.76,3.438 1.375,3.635 0.615,0.198 10 false IG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F68-2 (PGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F23-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE POWER STEERING ECU ASSEMBLY

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)