Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Combination Meter" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Combination Meter" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Combination meter assembly main line or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C366182E10
1.667,0.51 1.823,0.708 0.156,0.198 10 false 1 1.677,1.073 1.927,1.271 0.25,0.198 10 false 12 5.521,0.521 5.771,0.719 0.25,0.198 10 false 32 5.521,1.052 5.771,1.25 0.25,0.198 10 false 31 5.813,0.552 6.313,0.75 0.5,0.198 10 false CANH 5.813,1.26 6.313,1.458 0.5,0.198 10 false CANL 5.833,2.229 6.333,2.427 0.5,0.198 10 false IG+ 5.833,2.813 6.333,3.01 0.5,0.198 10 false B 5.833,3.292 6.333,3.49 0.5,0.198 10 false ET 5.521,2.135 5.771,2.333 0.25,0.198 10 false 39 5.531,2.667 5.781,2.865 0.25,0.198 10 false 40 5.51,3.208 5.76,3.406 0.25,0.198 10 false 21 5.583,3.667 5.833,3.865 0.25,0.198 10 false F4 5.583,3.844 6.75,4.26 1.167,0.417 10 false Combination Meter Assembly 4.427,2.385 5.344,2.583 0.917,0.198 10 false METER-IG2 4.292,2.917 5.458,3.083 1.167,0.167 10 false ECU-DCC NO. 2 2.125,2.229 3.708,2.479 1.583,0.25 10 false from IG2-NO. 2 Relay 2.667,2.75 4.25,3 1.583,0.25 10 false from Battery 0.177,1.583 0.844,1.75 0.667,0.167 10 false F114 0.177,1.75 2.177,1.917 2,0.167 10 false No. 3 CAN Junction Connector

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.
C328874C66
1.458,0.167 1.958,0.417 0.5,0.25 1.75,1.344 1.396,1.833 true 1.958,1.344 2.323,1.865 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 1.646,0.219 1.958,0.375 0.313,0.156 10 false F4 1.073,1.854 1.521,2.01 0.448,0.156 10 false CANL 2.323,1.875 2.771,2.031 0.448,0.156 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-32 (CANH) - F4-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (COMBINATION METER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C328874C67
1.448,0.24 1.948,0.49 0.5,0.25 2.708,1.833 2.854,1.354 true 3.188,1.823 3.021,1.354 true 0.542,1.865 0.406,1.344 true 0.104,0.052 0.417,0.208 0.313,0.156 10 false *a 1.615,0.271 1.927,0.438 0.313,0.167 10 false F4 2.625,1.865 2.938,2.031 0.313,0.167 10 false IG+ 3.156,1.854 3.354,2.042 0.198,0.188 10 false B 0.448,1.896 0.719,2.063 0.271,0.167 10 false ET
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-21 (ET) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-40 (B) - Body ground Always 11 to 14 V
F4-39 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)