The ECM receives a signal from the transmission revolution sensor (NT) installed in the continuously variable transaxle to control the lock-up engagement pressure and forward and reverse clutch pressure.
The transmission revolution sensor (NT) detects the continuously variable transaxle input shaft speed and sends a signal to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0717 | Input / Turbine Speed Sensor "A" Circuit No Signal | All of the following conditions are met (1 trip detection logic):
·
Vehicle is driven with the shift lever in D ·
Output shaft speed is 300 rpm or more ·
No malfunctions are found in the park/neutral position switch ·
Input turbine speed indicated by the transmission revolution sensor (NT) is less than 300 rpm for 2 seconds |
·
Wire harness or connector ·
Continuously variable transaxle assembly (Transmission revolution sensor (NT)) ·
ECM |
Comes on | DTC stored |
| P07BF | Input/Turbine Speed Sensor "A" Circuit Low | There is no malfunction in transmission revolution sensor (NT) signals, and the transmission revolution sensor (NT) output voltage is less than 0.2 V for 2 seconds (1 trip detection logic). | ·
Wire harness or connector ·
Continuously variable transaxle assembly (Transmission revolution sensor (NT)) ·
ECM |
Comes on | DTC stored |
| P07C0 | Input/Turbine Speed Sensor "A" Circuit High | There is no malfunction in transmission revolution sensor (NT) signals, and the transmission revolution sensor (NT) output voltage is higher than 1.8 V for 2 seconds (1 trip detection logic). | ·
Wire harness or connector ·
Continuously variable transaxle assembly (Transmission revolution sensor (NT)) ·
ECM |
Comes on | DTC stored |
The transmission revolution sensor (NT) detects the transaxle input shaft speed. The ECM determines the necessary gear ratio based on a comparison of the transmission revolution sensor (NT) (input shaft speed) with the transmission revolution sensor (NOUT) (output shaft speed).
When the output shaft speed is higher than the expected value and the input shaft speed is less than 300 rpm while driving with the shift lever in D, the ECM will determine that the transmission revolution sensor (NT) is malfunctioning. The ECM will illuminate the MIL and store a DTC.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Drive the vehicle for 2 seconds or more at 6 km/h (4 mph) or more with the shift lever in D.
Check for DTCs again.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| SPD (NT) |
| NT Sensor Voltage |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| SPD (NT) | Input turbine speed | Min.: 0 rpm
Max.: 12750 rpm |
·
Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine) ·
Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N) ·
0 rpm: Vehicle stopped with shift lever in R |
Data is displayed in increments of 50 rpm. |
| NT Sensor Voltage | Input turbine speed (NT) sensor output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| Result | Proceed to |
|---|---|
| Data display is not within Normal Condition range | A |
| Data display is within Normal Condition range | B |
A
B
Remove the transmission revolution sensor (NT).
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>REVOLUTION SENSOR>REMOVAL
Connect the battery to the sensor as shown in the illustration.
| *1 | Battery | - | - |
| *a | Component without harness connected
(Transmission Revolution Sensor (NT)) |
*b | Magnet |
| *c | 5 mm or less | *d | Ammeter |
Wave a magnetic object left and right in front of the transmission revolution sensor (NT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.
Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.
Measure the current according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (NTO) - 2 (NTB) | Low signal | 4 to 8 mA |
| 1 (NTO) - 2 (NTB) | High signal | 12 to 16 mA |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C47 transmission revolution sensor (NT) connector.
Disconnect the C63 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C47-1 (NTO) - C63-125 (NTO) | Always | Below 1 Ω |
| C47-2 (NTB) - C63-126 (NTB) | Always | Below 1 Ω |
| C47-1 (NTO) or C63-125 (NTO) - Body ground and other terminals | Always | 10 kΩ or higher |
| C47-2 (NTB) or C63-126 (NTB) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT