The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is output by the oil pressure sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0842 | Transmission Fluid Pressure Sensor/Switch "A" Circuit Low | When 2 seconds or more have elapsed after engine start, there is a short in the oil pressure sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Wire harness or connector ·
Oil pressure sensor ·
ECM |
Comes on | DTC stored |
| P0843 | Transmission Fluid Pressure Sensor/Switch "A" Circuit High | When 2 seconds or more have elapsed after engine start, there is an open or a short to +B in the oil pressure sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Wire harness or connector ·
Oil pressure sensor ·
ECM |
Comes on | DTC stored |
These DTCs indicate an open or short in the oil pressure sensor circuit. If there is an open or short in the oil pressure sensor circuit, the ECM detects the malfunction, illuminates the MIL and stores a DTC.
Do not perform a stall test if there are any people or objects near the vehicle.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform a stall test if any wheel chocks are out of position.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
The vehicle could begin moving suddenly, resulting in a serious accident.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Start the engine and wait for 2 seconds or more.
Check for DTCs again.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Do not perform a stall test if there are any people or objects near the vehicle.
Do not perform a stall test if any wheel chocks are out of position.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
This test must be conducted after checking and confirming that the engine is operating normally.
Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).
Perform this test with the A/C off.
Do not perform the stall speed test for longer than 5 seconds.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
| Tester Display |
|---|
| Connect the TC and TE1 |
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.
| Tester Display |
|---|
| A/T Oil Pressure |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Pressure | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.9 to 4.7 MPa (39.8 to 47.9 kgf/cm2, 566 to 682 psi): D position stall speed test ·
3.7 to 4.9 MPa (37.7 to 50.0 kgf/cm2, 537 to 711 psi): R position stall speed test |
- |
| Result | Proceed to |
|---|---|
| Data display is not within Normal Condition range | A |
| Data display is within Normal Condition range | B |
A
B
Disconnect the C44 oil pressure sensor connector.
Disconnect the C63 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C44-1 (E2) - C63-109 (EPTO) | Always | Below 1 Ω |
| C44-2 (PTO) - C63-79 (PTO) | Always | Below 1 Ω |
| C44-3 (VC) - C63-110 (VCPT) | Always | Below 1 Ω |
| C44-1 (E2) or C63-109 (EPTO) - Body ground and other terminals | Always | 10 kΩ or higher |
| C44-2 (PTO) or C63-79 (PTO) - Body ground and other terminals | Always | 10 kΩ or higher |
| C44-3 (VC) or C63-110 (VCPT) - Body ground and other terminals | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C63-79 (PTO) - Body ground | Ignition switch ON | Below 1 V |
| C44-2 (PTO) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Oil Pressure Sensor) |
Disconnect the oil pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C44-3 (VC) - C44-1 (E2) | Ignition switch ON | 4.75 to 5.25 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the oil pressure sensor.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT