Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2020.08
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292534 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical  


DESCRIPTION

The ECM uses the shift solenoid valve SLU to perform forward and reverse clutch control or lock-up clutch control.

C300480C04
5.417,2.198 5.563,1.031 true 4.51,1.302 3.969,0.375 3.969,0.375 3.719,0.375 true 4.083,1.563 3.969,2.208 3.969,2.208 3.719,2.208 true 5.594,1.615 5.427,2.208 5.427,2.208 5.177,2.208 true 0.813,1.229 1.063,1.448 0.25,0.219 10 false *a 1.594,2.031 2.24,2.271 0.646,0.24 10 false *b 3.542,0.313 3.854,0.51 0.313,0.198 10 false *1 3.542,2.135 3.854,2.333 0.313,0.198 10 false *2 4.979,2.135 5.292,2.333 0.313,0.198 10 false *3
*1 Spool Valve *2 Sleeve
*3 Solenoid Coil - -
*a Hydraulic Pressure *b Current Flow to Solenoid


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical While the vehicle is driven, there is an open or short in the shift solenoid valve SLU circuit for 1 second or more (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SLU)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SLU circuit. If there is an open or short in the shift solenoid valve SLU circuit, the ECM detects the malfunction, illuminates the MIL and stores this DTC.

WIRING DIAGRAM

C328132E31
0.25,1.594 1.906,1.823 1.656,0.229 10 false Shift Solenoid Valve SLU 4.323,1 4.938,1.198 0.615,0.198 10 false SLU+ 4.781,1 4.938,1.198 0.156,0.198 10 false 4 5.146,1 5.458,1.198 0.313,0.198 10 false 43 5.438,1 6.052,1.198 0.615,0.198 10 false SLU+ 4.323,1.969 4.938,2.167 0.615,0.198 10 false SLU- 5.438,1.969 6.052,2.167 0.615,0.198 10 false SLU- 4.76,1.969 5.073,2.167 0.313,0.198 10 false 11 5.156,1.969 5.469,2.167 0.313,0.198 10 false 42 2.708,2.448 3.24,2.646 0.531,0.198 10 false C40 2.719,2.604 4.021,2.844 1.302,0.24 10 false Transmission Wire 1.198,3.063 3.927,3.375 2.729,0.313 10 false Continuously Variable Transaxle Assembly 5.917,3.042 6.531,3.24 0.615,0.198 10 false C63 5.917,3.188 6.333,3.458 0.417,0.271 10 false ECM 5.99,0.74 6.604,0.938 0.615,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle and confirm the lock-up on and off conditions according to Road Test.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C298188C09
1.094,0.365 1.49,0.917 true 1.125,1.771 1.49,1.281 true 0.719,0.281 1.24,0.479 0.521,0.198 10 false SLU+ 0.76,1.74 1.219,1.938 0.458,0.198 10 false SLU- 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Component without harness connected
(Transmission Wire)


Disconnect the C40 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SLU+) - 11 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
4 (SLU+) - Body ground and other terminals Always 10 kΩ or higher
11 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C364977C10
1.333,0.094 1.75,0.333 0.417,0.24 1.146,1.021 0.844,1.771 true 1.229,1.021 1.99,1.781 true 1.438,0.135 1.896,0.333 0.458,0.198 10 false C63 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.604,1.833 1.375,2.021 0.771,0.188 10 false 42 (SLU-) 1.729,1.844 2.521,2.104 0.792,0.26 10 false 43 (SLU+)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C63-43 (SLU+) - C63-42 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C63-43 (SLU+) - Body ground and other terminals Always 10 kΩ or higher
C63-42 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT