Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge) › from 2020.08
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292452 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of continuously variable transaxle assembly Perform the following procedures in the order shown:
1.

Reset memory

2.

Deceleration sensor zero point calibration

3.

CVT oil pressure calibration


Deterioration of fuel efficiency (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the continuously variable transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Simple intelligent parking assist system*1 Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 11361J 1.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C297722

Remove the flywheel housing under cover.


Hide 32101G 2.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C300744

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.



Hide 3.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 16267 4.DISCONNECT NO. 3 WATER BY-PASS HOSE

a.
C315507

Slide the clip and disconnect the No. 3 water by-pass hose from the oil cooler.


Hide 16282 5.DISCONNECT NO. 5 WATER BY-PASS HOSE

a.
C315508

Slide the hose clip and disconnect the No. 5 water by-pass hose from the transmission oil cooler.


b.

Disengage the 2 clamps to disconnect the No. 5 water by-pass hose from the continuously variable transaxle assembly.


Hide 82121 6.DISCONNECT ENGINE WIRE

a.

Disconnect the park/neutral position switch connector.

C365130C01
1.167,2.083 1.375,2.281 0.208,0.198 10 true *1 1.594,2.229 1.802,2.427 0.208,0.198 10 true *2 2.344,1.063 2.521,1.24 0.177,0.177 10 true *3 6.448,0.917 6.688,1.083 0.24,0.167 10 true *4 1.385,1.229 1.594,1.396 0.208,0.167 10 true *5 4.792,1.979 5.01,2.146 0.219,0.167 10 true *6
*1 Park/Neutral Position Switch Connector *2 Transmission Wire Connector
*3 Transmission Revolution Sensor (NIN) Connector *4 Transmission Revolution Sensor (NOUT) Connector
*5 Transmission Revolution Sensor (NT) Connector *6 Oil Pressure Sensor Connector



b.

Disconnect the transmission wire connector.


c.

Disconnect the transmission revolution sensor (NIN) connector.


d.

Disconnect the transmission revolution sensor (NT) connector.


e.

Disconnect the transmission revolution sensor (NOUT) connector.


f.

Disconnect the oil pressure sensor connector.


g.

Remove the 3 bolts and nut to disconnect the engine wire from the continuously variable transaxle assembly.


h.

Disengage the 5 clamps to disconnect the engine wire from the continuously variable transaxle assembly.


i.
C366690

Disengage the 3 clamps to disconnect the engine wire from the front suspension crossmember sub-assembly.


Hide 28100 7.REMOVE STARTER ASSEMBLY

Hide 11363A 8.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 12325A 9.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C365132

Remove the 5 bolts and transverse engine engine mounting bracket from the continuously variable transaxle assembly.


Hide 10.REMOVE ENGINE ASSEMBLY

a.
C318474E01
1.031,0.021 1.188,0.219 0.156,0.198 10 true A 0.625,0.625 0.781,0.823 0.156,0.198 10 true B 2.365,0 2.521,0.198 0.156,0.198 10 true A 2.583,0.104 2.74,0.302 0.156,0.198 10 true A 0.792,1.625 0.948,1.823 0.156,0.198 10 true B 1.073,1.969 1.229,2.167 0.156,0.198 10 true B 2.198,1.979 2.354,2.177 0.156,0.198 10 true B 2.594,1.865 2.75,2.063 0.156,0.198 10 true B

Remove the 8 bolts and engine assembly from the continuously variable transaxle assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.


HINT:
·

Bolt (A): Remove from continuously variable transaxle assembly side.

·

Bolt (B): Remove from engine assembly side.




Hide 32000A 11.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 30400E 12.REMOVE CVT OIL PUMP TYPE T OIL SEAL

CAUTION:
·

Do not remove the front oil pump assembly from the continuously variable transaxle assembly main body, as there is a possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a continuously variable transaxle assembly malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the continuously variable transaxle assembly.

·

Do not use cotton work gloves, cloths, paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter may enter the continuously variable transaxle assembly while the torque converter assembly is not attached to it.

·

Do not use an air gun until the torque converter assembly has been installed, as it may cause dust and foreign matter to be stirred up.



a.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


b.
C208788C02
2.406,2.073 2.406,2.604 false 0.979,1.25 1.302,0.781 1.302,0.781 1.563,0.781 false 1.802,2.531 1.542,2.531 1.542,2.531 1.271,1.865 false 2.302,2.646 2.76,2.844 0.458,0.198 10 false SST 1.604,0.677 1.99,1.104 0.385,0.427 10 false *1 1.844,2.417 2.271,2.833 0.427,0.417 10 false *a
*1 CVT Oil Pump Type T Oil Seal
*a Claw


Using SST, remove the CVT oil pump type T oil seal from the continuously variable transaxle assembly.

NOTICE:

Pay attention to the angle of the claws of SST when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles may be produced if they do.



Hide 51201 13.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C365145

Remove the bolt and front suspension crossmember sub-assembly from the No. 2 engine moving control rod.


Hide 12364B 14.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C365147

Remove the 4 bolts and No. 2 engine moving control rod from the continuously variable transaxle assembly.


Hide 33823 15.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C295568

Disengage the clamp from the No. 1 transmission control cable bracket.


b.

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 16.REMOVE TRANSMISSION CONTROL CABLE SUPPORT

a.
C315509

Remove the 2 bolts and transmission control cable support from the continuously variable transaxle assembly.


Hide 17.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C365123C01
1.833,4 2.219,3.719 true 2.573,3.594 2.917,3.333 false 2.917,2.083 2.167,1.292 true 0.688,1.083 1,1.083 true 0.25,0.458 0.5,0.594 true 2.938,3.198 3.177,3.396 0.24,0.198 10 false *1 0.073,0.344 0.385,0.5 0.313,0.156 10 false *2 1.01,0.99 1.24,1.167 0.229,0.177 10 true *3 1.635,3.969 1.875,4.167 0.24,0.198 10 true *1 2.958,2.052 3.198,2.25 0.24,0.198 10 false *1
*1 Wire Harness Clamp Bracket
*2 Water By-pass Hose Clamp
*3 Water Hose Clamp Bracket


Remove the bolt and water hose clamp bracket from the continuously variable transaxle assembly.


b.

Remove the water by-pass hose clamp from the water hose clamp bracket.


c.

Remove the 3 bolts and 3 wire harness clamp brackets from the continuously variable transaxle assembly.


Hide 32921Y 18.REMOVE TUBE CONNECTOR

a.
C296963

Slide the clip and disconnect the No. 1 transmission oil cooler hose from the tube connector.

NOTICE:

Do not damage the coating of the hose insertion part of the tube connector.



b.

Remove the tube connector from the continuously variable transaxle assembly.


c.

Remove the O-ring from the tube connector.


Hide 32901F 19.REMOVE OIL COOLER ELBOW SUB-ASSEMBLY

a.
C296964

Slide the clip and disconnect the No. 2 transmission oil cooler hose from the oil cooler elbow sub-assembly.

NOTICE:

Do not damage the coating of the hose insertion part of the oil cooler elbow sub-assembly.



b.

Remove the union bolt, oil cooler elbow sub-assembly and gasket from the continuously variable transaxle assembly.


Hide 35151K 20.REMOVE AUTOMATIC TRANSMISSION CASE COVER

a.
C297207

Remove the 2 clips and automatic transmission case cover from the continuously variable transaxle assembly.


Hide 21.REMOVE STRAIGHT SCREW PLUG

HINT:

Perform this procedure only when replacement of the straight screw plug is necessary.


a.
C316583

Remove the straight screw plug and gasket from the continuously variable transaxle assembly.


Hide 35012B 22.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the transmission breather hose sub-assembly is necessary.


a.
C295577C02
2.51,0.51 2.875,0.51 false 2.938,0.438 3.25,0.635 0.313,0.198 10 false *1
*1 Transmission Breather Hose Sub-assembly


Remove the transmission breather hose sub-assembly from the continuously variable transaxle assembly.


b.
C365133C01
2.698,2 3.031,2 false 2,1.667 2.333,1.667 false 0.615,0.333 0.917,0.167 false 2.25,0.76 2.583,0.5 false 0.948,0.063 1.26,0.219 0.313,0.156 10 false *1 2.615,0.396 2.927,0.552 0.313,0.156 10 false *2 1.802,1.563 2.115,1.719 0.313,0.156 10 false *3 3.063,1.896 3.375,2.052 0.313,0.156 10 false *4
*1 No. 1 Breather Plug (CVT)
*2 Breather Plug Hose
*3 No. 2 Breather Plug (CVT)
*4 O-ring


Remove the No. 1 breather plug (CVT) and No. 2 breather plug (CVT) from the breather plug hose.


c.

Remove the O-ring from the breather plug.


Hide 32000A 23.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101B 24.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY