Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2020.08
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292534 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2767  Input / Turbine Speed Sensor "B" Circuit No Signal  


DESCRIPTION

The ECM detects the input shaft speed based on the signal from the transmission revolution sensor (NIN) and performs gear ratio control.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2767 Input / Turbine Speed Sensor "B" Circuit No Signal While the vehicle is driven with the shift lever in D, and the output shaft speed is 300 rpm or more (vehicle speed is approximately 6 km/h (4 mph) or more), the speed indicated by the transmission revolution sensor (NIN) is less than 300 rpm for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NIN)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NIN) installed to the continuously variable transaxle and determines the input shaft speed in order to control the gear ratio. If the ECM detects no signal from the transmission revolution sensor (NIN) even while the vehicle is moving, it will determine that there is a malfunction in the transmission revolution sensor (NIN), illuminate the MIL and store this DTC.

WIRING DIAGRAM

C328141E09
0.208,2.875 2.573,3.094 2.365,0.219 10 false Transmission Revolution Sensor (NIN) 0.229,2.698 0.646,2.896 0.417,0.198 10 false C45 5.969,2.927 6.385,3.125 0.417,0.198 10 false C63 5.969,3.083 6.385,3.281 0.417,0.198 10 false ECM 1.677,2.115 2.094,2.313 0.417,0.198 10 false NIN- 1.677,1.156 2.094,1.354 0.417,0.198 10 false NIN+ 5.656,1.156 6.073,1.354 0.417,0.198 10 false NIN+ 5.656,2.125 6.073,2.323 0.417,0.198 10 false NIN- 2.073,1.156 2.49,1.354 0.417,0.198 10 false 2 2.083,2.115 2.5,2.313 0.417,0.198 10 false 1 5.344,2.125 5.76,2.323 0.417,0.198 10 false 124 5.365,1.156 5.781,1.354 0.417,0.198 10 false 123

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle for 2 seconds or more at 6 km/h (4 mph) or more with the shift lever in D.



PROCEDURE

1.READ VALUE USING GTS (SPD (NIN), ENGINE SPEED AND LOCK UP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
SPD (NIN)
Lock Up
50003 234 9,400,417

e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
·

0 rpm: Engine stopped (ignition switch ON)

·

No large changes in engine speed: Driving at a constant speed


When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
SPD (NIN) Primary pulley speed (NIN) Min.: 0 rpm
Max.: 12750 rpm
·

0 rpm: Vehicle stopped

·

Primary pulley speed (NIN) equal to engine speed (NE): Lock-up ON (After warming up engine)


Data is displayed in increments of 50 rpm.
Lock Up Lock-up OFF or ON
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN)

B

5.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN)
a.
C200614C06
1.354,1.729 1.594,1.219 true 2.125,1.75 1.844,1.219 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.198,1.781 1.813,1.979 0.615,0.198 10 false NIN+ 2.021,1.781 2.635,1.979 0.615,0.198 10 false NIN-
*a Component without harness connected
(Transmission Revolution Sensor (NIN))


Disconnect the C45 transmission revolution sensor (NIN) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NIN-) - 2 (NIN+) 20°C (68°F) 560 to 680 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NIN)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)
a.
C364977C11
1.333,0.094 1.75,0.333 0.417,0.24 1.51,1.208 1.167,1.833 true 1.573,1.219 2.573,1.823 true 1.438,0.135 1.896,0.333 0.458,0.198 10 false C63 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.906,1.833 1.677,2.021 0.771,0.188 10 false 123 (NIN+) 2.354,1.844 3.146,2.104 0.792,0.26 10 false 124 (NIN-)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C63-123 (NIN+) - C63-124 (NIN-) 20°C (68°F) 560 to 680 Ω
C63-123 (NIN+) - Body ground and other terminals Always 10 kΩ or higher
C63-124 (NIN-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT