The CVT fluid temperature sensor converts the CVT fluid temperature into a resistance value for use by the ECM.
The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.
The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P071011 | Transmission Fluid Temperature Sensor "A" Circuit Short To Ground | There is a short in the CVT fluid temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Wire harness or connector ·
Continuously variable transaxle assembly (CVT fluid temperature sensor) ·
ECM |
Comes on | DTC stored | SAE Code:
P0712 |
The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and can detect a short to ground in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature is less than 79 Ω*, the ECM interprets this as a malfunction of the CVT fluid temperature sensor or wiring, illuminates the MIL and stores a DTC.
*: 150°C (302°F) or more is indicated regardless of the actual CVT fluid temperature.
The CVT fluid temperature can be checked in the Data List.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the ignition switch to ON and wait for 3 seconds or more.
Check for DTCs again.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Warm up the engine.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
| Tester Display |
|---|
| A/T Oil Temperature No.1 |
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Temperature No.1 | CVT fluid temperature sensor value | Min.: -40°C (-40°F)
Max.: 150°C (302°F) |
·
Approximately 100°C (212°F): After stall speed test ·
Equal to ambient temperature: After cold soak |
If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted. |
| Result | Proceed to |
|---|---|
| Data List value is not normal | A |
| Data List value is normal | B |
A
B
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C40 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (OIL) - 7 (E2) | Always | 79 Ω to 156 kΩ |
| 1 (OIL) - Body ground and other terminals | Always | 10 kΩ or higher |
| 7 (E2) - Body ground and other terminals | Always | 10 kΩ or higher |
If the resistance is out of the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may decrease.
| CVT Fluid Temperature | Specified Condition |
|---|---|
| 10°C (50°F) | 5.6 to 7.3 kΩ |
| 25°C (77°F) | 3.5 kΩ |
| 110°C (230°F) | 0.22 to 0.27 kΩ |
Connect the C40 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C62-84 (THO1) - C62-83 (ETHO) | Always | 79 Ω to 156 kΩ |
| C62-84 (THO1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-83 (ETHO) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the continuously variable transaxle assembly.
When Not Using the Engine Support Bridge
When Using the Engine Support Bridge
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT