Home › Drivetrain › K313 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2020.08
RM32H0E _52 Drivetrain _059624 K313 MULTIDRIVE / CVT _0292538 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P084000  Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance  P28287F  Pressure Control Solenoid "K" Actuator Stuck Off  


DESCRIPTION

The ECM controls the secondary oil pressure based on the secondary oil pressure signal output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P084000 Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance Either one of the following conditions is met (1 trip detection logic):
·

When the requested oil pressure is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more, the oil pressure sensor output is 0.5 MPa (5.1 kgf/cm2, 73 psi) or less for 2 seconds or more.

·

When the requested oil pressure is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less, the difference between the calculated primary pulley pressure and target primary pulley pressure is 2.0 MPa (20.4 kgf/cm2, 290 psi) or more for 3 seconds or more.


·

Oil pressure sensor

·

ECM


Comes on (Euro-OBD)
Does not come on (Except Euro-OBD)
DTC stored SAE Code:
P0841
P28287F Pressure Control Solenoid "K" Actuator Stuck Off One of the following conditions is met (1 trip detection logic):
·

When the requested oil pressure is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less, the oil pressure sensor output is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more for 3 seconds or more.

·

When the vehicle speed is less than 8 km/h (5 mph), the ratio of the transmission revolution sensor (NIN) output speed and transmission revolution sensor (NOUT) output speed exceeds a specified value for 0.2 seconds or more.

·

When the oil pressure sensor output is less than 0.35 MPa (3.6 kgf/cm2, 51 psi) and the target gear ratio is 2.0 or more, the actual gear ratio is less than 1.0 for 1.5 seconds or more.


·

Continuously variable transaxle assembly

·

ECM


Comes on (Euro-OBD)
Does not come on (Except Euro-OBD)
DTC stored SAE Code:
P2829

DTC Detection Condition Patterns (P084000):
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition The requested oil pressure value is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more. ○ -
The requested oil pressure value is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less. - ○
Malfunction Condition The oil pressure sensor output value is 0.5 MPa (5.1 kgf/cm2, 73 psi) or less. ○ -
The difference between the calculated primary pulley pressure and target primary pulley pressure is 2.0 MPa (20.4 kgf/cm2, 290 psi) or more. - ○
Duration 2 seconds or more 3 seconds or more
Detection Logic 1 trip detection logic 1 trip detection logic

HINT:

This DTC is output when either of the above detection patterns is met.


DTC Detection Condition Patterns (P28287F):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnostic Condition The requested oil pressure value is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less. ○ - -
The shift lever is in D, and the vehicle speed is less than 8 km/h (5 mph). - ○ -
The oil pressure sensor output value is less than 0.35 MPa (3.6 kgf/cm2, 51 psi) and the target gear ratio is 2.0 or more. - - ○
Malfunction Condition The oil pressure sensor output value is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more. ○ - -
The ratio of the transmission revolution sensor (NIN) output speed and transmission revolution sensor (NOUT) output speed exceeds a specified value. - ○ -
The actual gear ratio is less than 1.0. - - ○
Duration 3 seconds or more 0.2 seconds or more 1.5 seconds or more
Detection Logic 1 trip detection logic 1 trip detection logic 1 trip detection logic

HINT:

This DTC is output when any one of the above detection patterns is met.


MONITOR DESCRIPTION

The ECM checks for belt clamping high-pressure or low-pressure malfunctions. If a mechanical malfunction of the shift solenoid valve SLS or the oil pressure sensor is detected by the ECM, it illuminates the MIL* and stores a DTC.

*: Euro-OBD

CAUTION / NOTICE / HINT

CAUTION:
·
C328174

Do not perform a stall test if there are any people or objects near the vehicle.

·

The vehicle could begin moving suddenly, resulting in a serious accident.

·
C328171

Do not perform a stall test if any wheel chocks are out of position.

·

The vehicle could begin moving suddenly, resulting in a serious accident.

·
C328173

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.

·

The vehicle could begin moving suddenly, resulting in a serious accident.



NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P084000 AND P28287F)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

HINT:

If any DTCs other than P084000 or P28287F are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Both DTC P084000 and P28287F are output A
Only DTC P084000 is output B
Only DTC P28287F is output C
DTC P084000 and/or P28287F and other DTCs are output D



A

2.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)

B

12.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)

C

19.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)

D

2.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.

Powertrain > Transmission > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Belt Clamping Force Sensor
50004 373 22 367

g.

According to the display on the GTS, perform the Active Test.


h.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Belt Clamping Force Sensor Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 5.5 MPa (35.6 to 56.1 kgf/cm2, 507 to 798 psi): D position stall test

·

3.6 to 5.5 MPa (36.7 to 56.1 kgf/cm2, 522 to 798 psi): R position stall test


-

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

3.REPLACE ECM

B

4.REPLACE OIL PRESSURE SENSOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>COMPONENTS


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

Result:
Proceed to
NEXT



NEXT

6.PERFORM INITIALIZATION
6.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Airbag sensor assembly (Yaw rate and acceleration sensor)



·

After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.



a.

Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P084000 and/or P28287F is output A
DTCs are not output B



A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.PERFORM INITIALIZATION
9.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Airbag sensor assembly (Yaw rate and acceleration sensor)



·

After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.



a.

Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

10.CHECK DTC OUTPUT
10.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P28287F is output A
DTCs are not output B



A

11.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

B

END

11.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT

12.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.

Powertrain > Transmission > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Belt Clamping Force Sensor
50004 373 22 367

g.

According to the display on the GTS, perform the Active Test.


h.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Belt Clamping Force Sensor Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 5.5 MPa (35.6 to 56.1 kgf/cm2, 507 to 798 psi): D position stall test

·

3.6 to 5.5 MPa (36.7 to 56.1 kgf/cm2, 522 to 798 psi): R position stall test


-

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

13.REPLACE ECM

B

14.REPLACE OIL PRESSURE SENSOR
13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>COMPONENTS


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

Result:
Proceed to
NEXT



NEXT

16.PERFORM INITIALIZATION
16.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Airbag sensor assembly (Yaw rate and acceleration sensor)



·

After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.



a.

Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

17.CHECK DTC OUTPUT
17.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P084000 is output A
DTCs are not output B



A

18.REPLACE ECM

B

END

18.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

19.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.

Powertrain > Transmission > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Belt Clamping Force Sensor
50004 373 22 367

g.

According to the display on the GTS, perform the Active Test.


h.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Belt Clamping Force Sensor Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 5.5 MPa (35.6 to 56.1 kgf/cm2, 507 to 798 psi): D position stall test

·

3.6 to 5.5 MPa (36.7 to 56.1 kgf/cm2, 522 to 798 psi): R position stall test


-

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

20.REPLACE ECM

B

21.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
20.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

21.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT