Home › Drivetrain › K313 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2020.08–2021.09
RM32H0E _52 Drivetrain _059624 K313 MULTIDRIVE / CVT _0292538 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P084011  Transmission Fluid Pressure Sensor/Switch "A" Circuit Short To Ground  


DESCRIPTION

The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P084011 Transmission Fluid Pressure Sensor/Switch "A" Circuit Short To Ground When 2 seconds or more have elapsed after engine start, there is a short in the oil pressure sensor circuit for 0.5 seconds (1 trip detection logic).
·

Wire harness or connector

·

Oil pressure sensor

·

ECM


Comes on DTC stored SAE Code:
P0842

MONITOR DESCRIPTION

This DTC indicates a short in the oil pressure sensor circuit. If there is an open or short in the oil pressure sensor circuit, the ECM detects the malfunction, illuminates the MIL and stores a DTC.

WIRING DIAGRAM

C318995E22
1.094,2.802 2.781,3 1.688,0.198 10 false Oil Pressure Sensor 5.323,3.073 6.135,3.438 0.813,0.365 10 false ECM 1.094,2.667 1.552,2.865 0.458,0.198 10 false C44 5.323,2.927 6.042,3.219 0.719,0.292 10 false C62 4.885,2.167 5.5,2.365 0.615,0.198 10 false EPTO 4.885,1.615 5.5,1.813 0.615,0.198 10 false PTO 4.885,1.125 5.5,1.323 0.615,0.198 10 false VCPT 2.156,1.24 2.771,1.438 0.615,0.198 10 false VC 2.073,1.729 2.688,1.927 0.615,0.198 10 false PTO 2.177,2.271 2.792,2.469 0.615,0.198 10 false E2 2.448,2.167 3.063,2.365 0.615,0.198 10 false 1 2.448,1.615 3.063,1.813 0.615,0.198 10 false 2 2.438,1.135 3.052,1.333 0.615,0.198 10 false 3 4.573,1.125 5.188,1.323 0.615,0.198 10 false 118 4.646,1.615 5.26,1.813 0.615,0.198 10 false 86 4.573,2.167 5.188,2.365 0.615,0.198 10 false 117 5.583,0.948 6.198,1.146 0.615,0.198 10 false 5 V

CAUTION / NOTICE / HINT

CAUTION:
·
C328174

Do not perform a stall test if there are any people or objects near the vehicle.

·

The vehicle could begin moving suddenly, resulting in a serious accident.

·
C328171

Do not perform a stall test if any wheel chocks are out of position.

·

The vehicle could begin moving suddenly, resulting in a serious accident.

·
C328173

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.

·

The vehicle could begin moving suddenly, resulting in a serious accident.



NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Start the engine and wait for 2 seconds or more.



PROCEDURE

1.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)
CAUTION:

A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds.

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.

·

Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.

HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.



c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.

Powertrain > Transmission > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Belt Clamping Force Sensor
50004 373 22 367

g.

According to the display on the GTS, perform the Active Test.


h.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Belt Clamping Force Sensor Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 5.5 MPa (35.6 to 56.1 kgf/cm2, 507 to 798 psi): D position stall test

·

3.6 to 5.5 MPa (36.7 to 56.1 kgf/cm2, 522 to 798 psi): R position stall test


-

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)

B

6.REPLACE ECM
2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)
a.

Disconnect the C44 oil pressure sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C44-1 (E2) or C62-117 (EPTO) - Body ground and other terminals Always 10 kΩ or higher
C44-2 (PTO) or C62-86 (PTO) - Body ground and other terminals Always 10 kΩ or higher
C44-3 (VC) or C62-118 (VCPT) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the C62 ECM connector.


e.

Connect the C44 oil pressure sensor connector.


Result:
Proceed to
OK
NG



OK

3.CHECK ECM (VCPT TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (OIL PRESSURE SENSOR - ECM)

3.CHECK ECM (VCPT TERMINAL VOLTAGE)
a.
C125747C54
0.438,0.938 0.802,1.219 0.365,0.281 1.479,1.271 1.146,1.719 1.146,1.719 1.01,1.719 true 2.052,1.26 2.406,1.677 2.406,1.677 2.531,1.677 true 0.833,1.646 1.219,1.854 0.385,0.208 10 false E2 2.604,1.615 2.875,1.802 0.271,0.188 10 false VC 0.094,0.094 0.313,0.25 0.219,0.156 10 false *a 0.51,1.01 0.948,1.188 0.438,0.177 10 false C44
*a Front view of wire harness connector
(to Oil Pressure Sensor)


Disconnect the oil pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C44-3 (VC) - C44-1 (E2) Ignition switch ON 4.75 to 5.25 V



c.

Connect the oil pressure sensor connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE OIL PRESSURE SENSOR

NG

5.REPLACE ECM
4.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>COMPONENTS


Result:
Proceed to
NEXT



NEXT

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT