Home › Drivetrain › K313 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2020.08–2021.09
RM32H0E _52 Drivetrain _059624 K313 MULTIDRIVE / CVT _0292538 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P276531  Input/Turbine Speed Sensor "B" No Signal  


DESCRIPTION

The ECM detects the input shaft speed based on the signal from the revolution sensor (transmission revolution sensor (NIN)) and performs gear ratio control.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P276531 Input/Turbine Speed Sensor "B" No Signal While the vehicle is driven with the shift lever in D, and the output shaft speed is 300 rpm or more (vehicle speed is approximately 7 km/h (4.375 mph) or more), the speed indicated by the transmission revolution sensor (NIN) is less than 300 rpm for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NIN)

·

ECM


Comes on DTC stored SAE Code:
P2767

MONITOR DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NIN) installed to the continuously variable transaxle and determines the input shaft speed in order to control the gear ratio. If the ECM detects no signal from the transmission revolution sensor (NIN) even while the vehicle is moving, it will determine that there is a malfunction in the transmission revolution sensor (NIN), illuminate the MIL and store this DTC.

WIRING DIAGRAM

C318999E12
0.25,2.813 4.073,3.01 3.823,0.198 10 false Transmission Revolution Sensor (NIN) 5.979,3.073 6.885,3.344 0.906,0.271 10 false ECM 1.677,1.135 2.292,1.333 0.615,0.198 10 false NIN+ 5.667,1.135 6.281,1.333 0.615,0.198 10 false NIN+ 5.667,2.104 6.281,2.302 0.615,0.198 10 false NIN- 1.698,2.104 2.313,2.302 0.615,0.198 10 false NIN- 5.417,1.135 6.031,1.333 0.615,0.198 10 false 44 2.083,1.135 2.698,1.333 0.615,0.198 10 false 2 2.083,2.104 2.698,2.302 0.615,0.198 10 false 1 5.406,2.104 6.021,2.302 0.615,0.198 10 false 43 5.979,2.917 6.594,3.115 0.615,0.198 10 false C62 0.24,2.656 0.854,2.854 0.615,0.198 10 false C45 6.292,0.948 6.75,1.146 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle for 2 seconds or more at 7 km/h (4.375 mph) or more with the shift lever in D.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED, NIN SENSOR SPEED AND LOCK UP STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.

Powertrain > Transmission > Data List
Tester Display
Engine Speed
NIN Sensor Speed
Lock Up Status
50003 373 211,364,178

e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
680 to 780 rpm: Idling (shift lever in N, engine warmed up and A/C switch off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
NIN Sensor Speed Primary pulley speed (NIN) Min.: 0 rpm
Max.: 12750 rpm
·

0 rpm: Vehicle stopped

·

Primary pulley speed (NIN) equal to engine speed (NE): Lock-up ON (After warming up engine)


Data is displayed in increments of 50 rpm.
Lock Up Status Lock-up OFF or ON
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN)

B

5.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN)
a.
C221276C07
1.177,1.792 1.292,1.792 1.292,1.792 1.458,1.281 true 2.271,1.792 2.156,1.792 2.156,1.792 1.99,1.281 true 0.177,0.219 0.365,0.406 0.188,0.188 10 *a 0.802,1.719 1.156,1.896 0.354,0.177 10 NIN+ 2.323,1.719 2.646,1.875 0.323,0.156 10 NIN-
*a Component without harness connected
(Transmission Revolution Sensor (NIN))


Disconnect the C45 transmission revolution sensor (NIN) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NIN-) - 2 (NIN+) 20°C (68°F) 560 to 680 Ω



c.

Connect the C45 transmission revolution sensor (NIN) connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NIN)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)
a.
C326700C23
1.427,0.198 1.813,0.427 0.385,0.229 0.75,1.74 1.188,0.948 true 1.771,1.729 1.26,0.948 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 1.583,1.75 2.344,1.969 0.76,0.219 10 false 44 (NIN+) 0.583,1.75 1.344,1.969 0.76,0.219 10 false 43 (NIN-) 1.51,0.24 1.969,0.438 0.458,0.198 10 false C62
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-44 (NIN+) - C62-43 (NIN-) 20°C (68°F) 560 to 680 Ω
C62-44 (NIN+) - Body ground and other terminals Always 10 kΩ or higher
C62-43 (NIN-) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT