Home › Drivetrain › K313F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge) › from 2020.08
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0292474 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

K313F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: If the vehicle height has changed due to suspension or tire replacement

Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of continuously variable transaxle assembly Perform the following procedures in the order shown:
1.

Reset memory

2.

Deceleration sensor zero point calibration

3.

CVT oil pressure calibration


Deterioration of fuel efficiency (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.*1 Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the continuously variable transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 11361J 1.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A351509

Remove the flywheel housing under cover from the stiffening crankcase assembly.


Hide 32101G 2.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C327719

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.



Hide 3.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 82121 5.DISCONNECT ENGINE WIRE

a.

Disconnect the transmission wire connector.

C364040C01
2.25,0.844 2.563,1.042 0.313,0.198 10 true *1 2,1.688 2.313,1.885 0.313,0.198 10 true *2 2.25,2.375 2.563,2.573 0.313,0.198 10 true *3 4.417,0.542 4.729,0.74 0.313,0.198 10 true *4 4.813,2.177 5.125,2.375 0.313,0.198 10 true *5
*1 Park/Neutral Position Switch Connector *2 Transmission Wire Connector
*3 Transmission Revolution Sensor (NIN) Connector *4 Transmission Revolution Sensor (NOUT) Connector
*5 Oil Pressure Sensor Connector - -



b.

Disconnect the transmission revolution sensor (NIN) connector.


c.

Disconnect the park/neutral position switch connector.


d.

Disconnect the transmission revolution sensor (NOUT) connector.


e.

Disconnect the oil pressure sensor connector.


f.

Disengage the 7 clamps to disconnect the engine wire from the continuously variable transaxle assembly.


g.

Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.


h.
C366690

Disengage the 3 clamps to disconnect the engine wire from the front suspension crossmember sub-assembly.


Hide 6.DISCONNECT WATER HOSE

a.
C364042

Slide the 2 hose clips and disconnect the water hoses from the transmission oil cooler.


b.

Disengage the 2 clamps to separate the water hose from the continuously variable transaxle assembly.


Hide 28100 7.REMOVE STARTER ASSEMBLY (for Valeo Made Cold Area Specification Vehicles)

Hide 28100 8.REMOVE STARTER ASSEMBLY (for Valeo Made except Cold Area Specification Vehicles)

Hide 28100 9.REMOVE STARTER ASSEMBLY (for Denso Made without Stop and Start System)

Hide 11363A 10.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 11.REMOVE ENGINE ASSEMBLY

a.
C327721N01
0.885,0.063 1.042,0.26 0.156,0.198 10 true A 2.406,0.052 2.563,0.25 0.156,0.198 10 true A 0.552,0.854 0.708,1.052 0.156,0.198 10 true B 0.844,1.74 1,1.938 0.156,0.198 10 true B 1.365,1.979 1.521,2.177 0.156,0.198 10 true B 2.135,1.979 2.292,2.177 0.156,0.198 10 true B 2.583,1.917 2.74,2.115 0.156,0.198 10 true B

Remove the 7 bolts and engine assembly from the continuously variable transaxle assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.


HINT:
·

Bolt (A): Remove from continuously variable transaxle assembly side.

·

Bolt (B): Remove from engine assembly side.




Hide 32000A 12.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C327722

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 30400E 13.REMOVE CVT OIL PUMP TYPE T OIL SEAL

NOTICE:
·

Do not remove the front oil pump assembly from the CVT main body, as there is a possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.

·

Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.



a.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


b.
C329642N01
1.552,2.635 1.552,2.24 false 1.448,2.677 1.906,2.875 0.458,0.198 10 false SST

Using SST, remove the CVT oil pump type T oil seal.

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.



Hide 36100 14.REMOVE TRANSFER ASSEMBLY

Hide 36100A 15.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

Hide 51201 16.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C365144

Remove the bolt and front suspension crossmember sub-assembly from the No. 2 engine moving control rod.


Hide 12364B 17.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C365146

Remove the 4 bolts and No. 2 engine moving control rod from the continuously variable transaxle assembly.


Hide 18.REMOVE ENGINE MOUNTING STAY LH

a.
C365204

Remove the 2 bolts and engine mounting stay LH from the continuously variable transaxle assembly and transverse engine engine mounting bracket.


Hide 12325A 19.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C365205

Remove the 3 bolts and transverse engine engine mounting bracket from the continuously variable transaxle assembly.


Hide 20.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C364048

Remove the 4 bolts and 4 wire harness clamp brackets from the continuously variable transaxle assembly.


Hide 33823 21.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C327723

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 87101A 22.REMOVE NO. 1 HEATER BRACKET SUB-ASSEMBLY

a.
C327727

Separate the No. 1 breather plug (CVT) from the clamp.


b.
C327728

Remove the clamp from the No. 1 heater bracket sub-assembly.


c.
C327729

Remove the bolt and No. 1 heater bracket sub-assembly from the continuously variable transaxle assembly.


Hide 23.REMOVE STRAIGHT SCREW PLUG

HINT:

Perform this procedure only when replacement of the straight screw plug is necessary.


a.
C333413

Remove the straight screw plug and gasket from the continuously variable transaxle assembly.


Hide 35012B 24.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the transmission breather hose sub-assembly is necessary.


a.
C333414

Remove the transmission breather hose sub-assembly from the continuously variable transaxle assembly.


b.
C333415C01
0.823,0.969 0.823,0.635 false 2.615,1.115 2.948,1.115 false 1.688,1.51 1.688,1.177 false 2.646,1.667 2.979,1.667 false 0.76,0.99 1.073,1.146 0.313,0.156 10 false *1 1.635,1.542 1.948,1.698 0.313,0.156 10 false *2 3,1.052 3.313,1.208 0.313,0.156 10 false *3 3.021,1.604 3.333,1.76 0.313,0.156 10 false *4
*1 No. 1 Breather Plug (CVT)
*2 Breather Plug Hose
*3 No. 2 Breather Plug (CVT)
*4 O-ring


Remove the No. 1 breather plug (CVT) and No. 2 breather plug (CVT) from the breather plug hose.


c.

Remove the O-ring from the No. 2 breather plug (CVT).


Hide 32000A 25.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101B 26.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY