Home › Audio / Visual / Telematics › AUDIO / VIDEO › STEREO COMPONENT AMPLIFIER › from 2020.08
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0298050 STEREO COMPONENT AMPLIFIER A

AUDIO / VIDEO  STEREO COMPONENT AMPLIFIER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the stereo component amplifier assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

CAUTION:
B458500

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.


HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS.

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)

Hide 2.REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 86183D 3.REMOVE AUDIO AMPLIFIER COVER

a.
E353764C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull the audio amplifier cover in the direction indicated by the arrow (1) shown in the illustration to disengage the clips.


b.

Pull the audio amplifier cover in the direction indicated by the arrow (2) shown in the illustration to disengage the guide to remove the audio amplifier cover.


Hide 86280 4.REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET

a.
E425624

Disengage the clamp.


b.

Disconnect the 2 connectors.


c.
E426184C01
0.844,0.552 1.177,0.885 true 0.625,0.427 0.792,0.594 0.167,0.167 10 true *a
*a Lock Lever
V113147

Remove in this Direction


Disengage the claw and pull the lock lever to disconnect the connector as shown in the illustration.


d.
E426186C01
3.021,1.167 2.729,0.865 true 3.042,1.042 3.271,1.26 0.229,0.219 10 true *1
*1 Front Floor Carpet Assembly


Turn back the part of the front floor carpet assembly.


e.

Remove the 2 bolts and stereo component amplifier assembly with bracket.


Hide 86286 5.REMOVE NO. 2 AMPLIFIER BRACKET

a.
E426187

Remove the 2 screws and No. 2 amplifier bracket from the stereo component amplifier assembly.


Hide 86285 6.REMOVE NO. 1 AMPLIFIER BRACKET

a.
E426188

Remove the 2 screws and No. 1 amplifier bracket from the stereo component amplifier assembly.