The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front seat assembly removal/installation are shown below.
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Wear protective gloves. Sharp areas on the parts may injure your hands.
If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Power seat is available only on the driver side.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
71910A
2.REMOVE FRONT SEAT HEADREST ASSEMBLY
Remove the front seat headrest assembly from the front seat assembly.
72124
3.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER
Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.
Disengage the claws to remove the front outer seat track bracket cover.
72128A
4.REMOVE FRONT INNER SEAT TRACK BRACKET COVER
Disengage the claws to remove the front inner seat track bracket cover.
72138
5.REMOVE OUTER SEAT TRACK COVER
Operate the slide and vertical power seat switch knob and move the front seat assembly to the foremost position.
Disengage the claws and guide to remove the outer seat track cover.
72158
6.REMOVE INNER SEAT TRACK BRACKET COVER
Disengage the claws and guide to remove the inner seat track bracket cover.
7.REMOVE FRONT SEAT ASSEMBLY
Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly.
Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.
Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly.
Operate the slide and vertical power seat switch knob and move the front seat assembly to the center position.
Operate the reclining power seat switch knob and move the seatback to the upright position.
Operate the slide and vertical power seat switch knob and move the front seat assembly to the upper most position.
Disconnect the cable from the negative (-) battery terminal.
for 8NR-FTS:
for 3ZR-FAE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an SRS part is accidentally deployed, it may cause a serious injury.
Disconnect the front seat airbag assembly connector under the front seat assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
| *a | White Housing Lock |
| *b | Yellow CPA |
|
Slide |
Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)
Push down the white housing lock again and disconnect the connector.
Do not push down the part (A) shown in the illustration when disconnecting the connector.
Disconnect each connector and disengage each clamp under the front seat assembly.
Remove the front seat assembly as shown in the illustration.
2 or more people are required when carrying the front seat assembly out of the vehicle.
Protect the front seat leg.
Be careful not to damage the front seat assembly, body exterior or body interior.