Home › Audio / Visual / Telematics › TELEMATICS › TELEPHONE ANTENNA CORD › from 2020.08
RM32H0E _56 Audio / Visual / Telematics _060052 TELEMATICS _0294135 TELEPHONE ANTENNA CORD A

TELEMATICS  TELEPHONE ANTENNA CORD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the antenna cord sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedures not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.


HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS.

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1


-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 55401E 1.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 55086 2.REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 86101 3.REMOVE ANTENNA CORD SUB-ASSEMBLY

a.

Disengage the clamps to remove the antenna cord sub-assembly.

E353801


b.

Disconnect the connector.


Hide 63311C 4.REMOVE ROOF HEADLINING

Hide 86101J 5.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

a.

for Type A:

i.

Remove each adhesive tape from the roof headlining.

E361587C01
0,0 0,0 false
V100155

Adhesive Tape
V100136

Front



ii.

Remove the No. 2 antenna cord sub-assembly from the roof headlining.



b.

for Type B:

i.

Remove each adhesive tape from the roof headlining.

E353818C02
0,0 0,0 false
V100155

Adhesive Tape
V100136

Front



ii.

Remove the No. 2 antenna cord sub-assembly from the roof headlining.



Hide 86101D 6.REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY

a.

for Glass Antenna Type:

i.
E353812

Disconnect the connector of the No. 4 antenna cord sub-assembly.



b.
E353809

Disconnect the connector.


c.

Disengage the clamps.


d.
E353811C03
2.115,0.896 2.448,0.896 true 1.104,1.5 0.771,1.5 true 2.448,0.792 2.688,0.99 0.24,0.198 10 true *a 0.521,1.396 0.76,1.594 0.24,0.198 10 true *b
*a Guide
*b Clamp


Disconnect the connector of the floor wire.


e.

Remove the bolt.


f.

Disengage the clamp and guide to remove the No. 3 antenna cord sub-assembly.