Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › from 2020.08
RM32H0E _58 Vehicle Interior _059856 INTERIOR PANELS / TRIM _0293790 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the instrument panel safety pad sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

CAUTION:
B458500

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch off, the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.


HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS.

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1


-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1. TABLE OF BOLT, SCREW AND NUT

HINT:

All bolts and screws relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.

B558576E01
0.25,0.292 0.865,0.49 0.615,0.198 10 false Code 1.313,0.292 2.083,0.49 0.771,0.198 10 false Shape 3.604,0.292 4.375,0.49 0.771,0.198 10 false Shape 2.521,0.292 3.135,0.49 0.615,0.198 10 false Code 4.781,0.292 5.396,0.49 0.615,0.198 10 false Code 5.865,0.292 6.635,0.49 0.771,0.198 10 false Shape 0.281,0.99 0.74,1.188 0.458,0.198 10 false <A> 0.281,2.083 0.74,2.281 0.458,0.198 10 false <D> 2.563,0.99 3.021,1.188 0.458,0.198 10 false <B> 2.563,2.083 3.021,2.281 0.458,0.198 10 false <E> 4.813,1 5.271,1.198 0.458,0.198 10 false <C> 4.823,2.083 5.281,2.281 0.458,0.198 10 false <F> 1.667,0.677 1.979,0.875 0.313,0.198 10 false φ6 1.667,0.844 2.74,1.042 1.073,0.198 10 false (0.236) 1.667,1.125 2.083,1.333 0.417,0.208 10 false L=20 1.656,1.281 2.729,1.479 1.073,0.198 10 false (0.787) 4.01,0.677 4.323,0.875 0.313,0.198 10 false φ6 4,0.844 5.073,1.042 1.073,0.198 10 false (0.236) 4,1.125 4.417,1.333 0.417,0.208 10 false L=20 4,1.281 5.073,1.479 1.073,0.198 10 false (0.787) 6.25,0.677 6.563,0.875 0.313,0.198 10 false φ7 6.25,0.844 6.833,1.021 0.583,0.177 10 false (0.276) 6.25,1.125 6.667,1.333 0.417,0.208 10 false L=20 6.25,1.281 6.833,1.479 0.583,0.198 10 false (0.787) 1.667,1.792 1.979,1.99 0.313,0.198 10 false φ5 1.667,1.958 2.74,2.156 1.073,0.198 10 false (0.197) 1.667,2.24 2.177,2.417 0.51,0.177 10 false L=14 1.667,2.396 2.74,2.594 1.073,0.198 10 false (0.551) 4,1.792 4.313,1.99 0.313,0.198 10 false φ8 4,1.958 5.073,2.156 1.073,0.198 10 false (0.315) 4,2.24 4.396,2.406 0.396,0.167 10 false L=21 4,2.396 5.073,2.594 1.073,0.198 10 false (0.827) 6.25,1.792 6.563,1.99 0.313,0.198 10 false φ6 6.25,1.958 6.833,2.208 0.583,0.25 10 false (0.236) 6.25,2.24 6.667,2.448 0.417,0.208 10 false L=15 6.25,2.406 6.833,2.604 0.583,0.198 10 false (0.591) 5.583,2.917 6.917,3.167 1.333,0.25 10 false mm (in.) (L=Length)


Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


Hide 4.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 84140 5.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 67913 6.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL


Hide 62111C 7.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL


Hide 55607 8.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B459256C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the claws and guides to remove the No. 2 instrument panel under cover sub-assembly as shown in the illustration.


Hide 55550 9.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B459191

Disengage the claw to disconnect the glove compartment door stopper sub-assembly.


b.
B459192C01
2.594,0.76 2.813,0.438 true 0.646,0.833 0.427,0.542 true 2.823,0.292 3.063,0.469 0.24,0.177 10 true *a 0.188,0.438 0.427,0.615 0.24,0.177 10 true *a
*a Stopper Portion
V100135

Push


Disengage the stoppers and pull out the glove compartment door assembly until it is level.


c.
B459193C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the hinges to remove the glove compartment door assembly as shown in the illustration.


Hide 55054 10.REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

a.
B459195

Disengage the claw to remove the glove compartment door stopper sub-assembly.


Hide 55433B 11.REMOVE NO. 2 INSTRUMENT PANEL LOWER FINISH PANEL

a.
B459196C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 5 screws <D>.


b.

Disengage the clips and claws to remove the No. 2 instrument panel lower finish panel as shown in the illustration.


c.

Disconnect the connector.


Hide 12.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B461389

Disconnect the front door opening trim weatherstrip LH from the area shown in the illustration.


Hide 62311B 13.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 55436A 14.REMOVE INSTRUMENT PANEL FINISH END PANEL LH

a.
B459198C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Using a molding remover A, disengage the clips and guides to remove the instrument panel finish end panel LH as shown in the illustration.


Hide 55435A 15.REMOVE INSTRUMENT PANEL FINISH END PANEL RH

HINT:

Use the same procedure as for the LH side.


Hide 55318C 16.REMOVE INSTRUMENT SIDE PANEL LH

a.
B459200C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Using a molding remover A, disengage the clips and guides to remove the instrument side panel LH as shown in the illustration.


b.

w/ Airbag Cut Off Switch:

i.

Disconnect the connector.



Hide 55317A 17.REMOVE INSTRUMENT SIDE PANEL RH

HINT:

Use the same procedure as for the LH side.


Hide 62212 18.REMOVE FRONT PILLAR GARNISH LH

a.
B459202C01
0,0 0,0 false
V100135

Pull up


Pull up the front pillar garnish LH to disengage the clips as shown in the illustration.


b.
B459203C01
0.344,0.833 0.604,0.563 true 0.365,0.833 0.667,0.958 true 0.146,0.74 0.344,0.927 0.198,0.188 10 true *a
*a Release Lever
V100135

Push


Push the release lever and separate the front pillar garnish clips from the vehicle body as shown in the illustration.

NOTICE:

If the front pillar garnish clip has significant damage, replace it with a new one.



c.

When the front pillar garnish clip cannot be removed using your fingers:

i.
B467723C01
0,0 0,0 false
V113147

Lift in this Direction


While pressing the part shown in the illustration with your finger, move the front pillar garnish clip in the direction indicated by the arrow shown in the illustration.


ii.
B467722C01
0,0 0,0 false
V113147

Remove in this Direction


While pulling the front pillar garnish clip in the direction indicated by the arrow, push the part shown in the illustration with the end of a screwdriver and remove the front pillar garnish clip.

NOTICE:

If the front pillar garnish clip has significant damage, replace it with a new one.




d.
B459204C01
0,0 0,0 false
V100135

Remove in this Direction


Disengage the guides to remove the front pillar garnish LH as shown in the illustration.


e.

w/ Speaker:

i.

Disconnect the connector.



f.

Remove the front pillar garnish clip.


g.
B459207C01
1.365,1.156 1.156,1.344 true 1.031,1.344 1.229,1.542 0.198,0.198 10 true *a
*a Protective Cover
V100155

Adhesive Tape


Protect the curtain shield airbag assembly.

i.

Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.




Hide 62211 19.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 55408F 20.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.
B459208C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the clips, claws and guides to remove the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.


b.

w/ Speaker:

i.

Disconnect the connector.



Hide 55409F 21.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:

Use the same procedure as for the No. 1 instrument panel speaker panel sub-assembly side.


Hide 86160P 22.REMOVE NO. 2 FRONT SPEAKER ASSEMBLY (w/ Woofer)

Hide 55404D 23.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
B459210C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips to remove the instrument cluster finish panel sub-assembly as shown in the illustration.


b.

w/ Switch:

i.

Disconnect each connector.



Hide 55410C 24.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B459212C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to separate the meter hood spacer as shown in the illustration.


b.
B459214C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 clips.


c.

Disengage the clips and guides to remove the instrument cluster finish panel assembly as shown in the illustration.


Hide 55012A 25.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

a.
B459216C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips to remove the No. 2 instrument panel garnish sub-assembly as shown in the illustration.


Hide 55414C 26.REMOVE STARTER SWITCH BEZEL (for RHD with Entry and Start System)

a.
B459218C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips to remove the starter switch bezel as shown in the illustration.


b.

Disconnect the connector.


Hide 83100 27.REMOVE COMBINATION METER ASSEMBLY

Hide 53601 28.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B459220C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw and guides to disconnect the hood lock control lever sub-assembly as shown in the illustration.


Hide 55545 29.REMOVE FUSE BOX OPENING COVER (w/ Knee Airbag)

a.
B459222C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the screw <D>.


b.

Disengage the clips to remove the fuse box opening cover as shown in the illustration.


c.

Disconnect each connector.


Hide 73997 30.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY WITH DOOR (w/ Knee Airbag)

Hide 55545 31.REMOVE FUSE BOX OPENING COVER (w/o Knee Airbag)

a.
B459224C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the screw <D>.


b.

Disengage the clips and claws to remove the fuse box opening cover with instrument panel lower finish panel sub-assembly as shown in the illustration.


c.

Disconnect each connector.


Hide 55045 32.REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)

a.
B459226

Remove the 2 screws <D>.


b.

Disengage the clips to remove the instrument panel lower finish panel sub-assembly from the fuse box opening cover.


Hide 55405B 33.REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY (w/o Display)

a.
B459229C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Disengage the claws to remove the instrument cluster finish center panel sub-assembly as shown in the illustration.


Hide 86120 34.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)

Hide 55521C 35.REMOVE STEREO OPENING COVER WITH BRACKET (w/ Cover)

a.
B459231

Remove the 4 bolts <A>.


b.

Disengage the guides to remove the stereo opening cover with bracket.


c.

Disconnect the connector.


Hide 86211 36.REMOVE NO. 1 RADIO BRACKET (w/ Cover)

a.
B459232

Remove the 3 screws <D>.


b.

Disengage the guides to remove the No. 1 radio bracket.


Hide 86212 37.REMOVE NO. 2 RADIO BRACKET (w/ Cover)

a.
B459233

Remove the 3 screws <D>.


b.

Disengage the guides to remove the No. 2 radio bracket.


Hide 86211 38.REMOVE NO. 1 RADIO BRACKET (w/o Cover)

a.
B459234

Remove the 2 bolts <A>.


b.

Disengage the guides to remove the No. 1 radio bracket.


Hide 86212 39.REMOVE NO. 2 RADIO BRACKET (w/o Cover)

a.
B459235

Remove the 2 bolts <A>.


b.

Disengage the guides to remove the No. 2 radio bracket.


Hide 55406B 40.REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY

a.
B459236C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips to remove the instrument cluster finish lower center panel sub-assembly as shown in the illustration.


b.

Disconnect the connector.


Hide 55414C 41.REMOVE STARTER SWITCH BEZEL (for LHD with Entry and Start System)

a.
B459238C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips to remove the starter switch bezel as shown in the illustration.


b.

Disconnect the connector.


Hide 55011A 42.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (w/o Display)

a.
B459242C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips and guides to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.


Hide 55670A 43.REMOVE INSTRUMENT PANEL CENTER REGISTER ASSEMBLY

a.
B478035C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 screws <D>.


b.

Disengage the claws and guides to remove the instrument panel center register assembly as shown in the illustration.


Hide 86140A 44.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)

Hide 55011A 45.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (w/ Display)

a.
B512684C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 bolts <A>.


b.

Disengage the clips and guides to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.


Hide 55085 46.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
B459244C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the No. 2 heater to register duct sub-assembly as shown in the illustration.


Hide 55401E 47.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

a.

for TMMT Made:

B459246C02
3.698,3.542 3.948,3.354 true 4.552,3.135 4.802,2.896 true 3.813,3.115 3.667,2.927 true 3.823,0.802 4.188,1.344 true 6.354,0.49 6.688,0.49 true 0.583,2.677 0.885,2.854 0.302,0.177 10 true <A> 1.594,1.938 2.365,2.104 0.771,0.167 10 true <B> or <C> 2.51,2.917 3.323,3.104 0.813,0.188 10 true <B> or <C> 4.198,0.844 4.708,1.021 0.51,0.177 10 true <F> *A 6.073,0.031 6.427,0.208 0.354,0.177 10 true <F> 6.313,2.656 6.625,2.823 0.313,0.167 10 true <A> 3.677,2.573 4.448,2.74 0.771,0.167 10 true <B> or <C> 5.375,2.115 6.146,2.281 0.771,0.167 10 true <B> or <C> 3.229,3.292 3.542,3.469 0.313,0.177 10 true <E> 4.698,3.427 5.01,3.604 0.313,0.177 10 true <E> 3.49,3.531 3.698,3.729 0.208,0.198 10 true *a 3.448,2.813 3.656,3.01 0.208,0.198 10 true *b 4.781,2.792 4.99,2.99 0.208,0.198 10 true *b 6.74,0.427 6.948,0.625 0.208,0.198 10 true *c 3.615,0.677 3.823,0.875 0.208,0.198 10 true *d
*A w/o Radio Receiver - -
*a Slider *b Airbag Bolt
*c Ground Bolt A *d Ground Bolt B


i.

Remove the 4 clips.


ii.

w/o Radio Receiver:

1.

Remove the ground bolt B as shown in the illustration.



iii.

Remove the 8 bolts and ground bolt A as shown in the illustration.


iv.

Slide the slider to disconnect the airbag connector.



b.

except TMMT Made:

B558574C01
2.302,3.344 2.531,3.219 true 3.479,3.406 3.281,3.313 true 6.76,0.594 6.344,0.385 true 3.188,3.552 3.063,3.375 true 0.635,2.74 0.938,2.896 0.302,0.156 10 true <A> 6.406,2.448 6.708,2.604 0.302,0.156 10 true <A> 2.51,2.833 2.813,2.99 0.302,0.156 10 true <E> 3.365,2.906 3.667,3.063 0.302,0.156 10 true <E> 3.875,2.813 5.125,2.99 1.25,0.177 10 true <B> or <C> 2.5,2.563 3.292,2.75 0.792,0.188 10 true <B> or <C> 0.969,2.167 1.781,2.354 0.813,0.188 10 true <B> or <C> 4.813,1.74 5.615,1.927 0.802,0.188 10 true <B> or <C> 6.344,0.073 6.646,0.229 0.302,0.156 10 true <F> 6.802,0.563 7.042,0.75 0.24,0.188 10 true *c 2.156,3.333 2.396,3.521 0.24,0.188 10 true *b 3.49,3.333 3.677,3.531 0.188,0.198 10 true *b 3.135,3.552 3.344,3.74 0.208,0.188 10 true *a
*a Slider *b Airbag Bolt
*c Ground Bolt - -


i.

Remove the 4 clips.


ii.

Remove the 9 bolts as shown in the illustration.


iii.

Slide the slider to disconnect the airbag connector.



c.

Disconnect each connector.


d.

Disengage each clamp.


e.

Disengage the guides to remove the instrument panel safety pad sub-assembly as shown in the illustration.

B559141C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)