The steering lock actuator or upper bracket assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little, as is done for a vehicle with a mechanical key, to change the position of the lock hole.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Steering Lock does not Lock | Entry&Start
·
Lock Request Receive ·
S Code Check ·
L Code Check ·
Steering Lock Main Body
·
FL Door Courtesy SW (for LHD) ·
FR Door Courtesy SW (for RHD) Power Source Control
·
Shift P Signal |
- |
When using the GTS with the engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Perform either of the following operations to lock/unlock the steering:
To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).
To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
When replacing the steering lock ECU (steering lock actuator or upper bracket assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), registration must be performed (refer to Service Bulletin).
After performing repairs, confirm that the problem does not recur.
Inspect the fuses for circuits related to this system before performing the following procedure.
When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
Use the Data List to check if the steering lock command is functioning properly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Lock Request Receive | Reception state of steering lock request signal by certification ECU (smart key ECU assembly) sent to ID code box (immobiliser code ECU)
|
OK or NG | OK: Lock request received within 10 seconds of opening any door with engine switch off and shift lever in P
NG: Except above |
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Lock Request Receive |
The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to on (ACC) or off and opening a door with the shift lever in P, and OK is displayed on the GTS screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Use the Data List to check if S code certification is functioning properly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| S Code Check |
OK is displayed on the GTS.
Reasons for verification failure:
The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Use the Data List to check if L code certification is functioning properly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| L Code Check |
OK is displayed on the GTS.
Reasons for verification failure:
The steering lock ECU (steering lock actuator or upper bracket assembly) or ID code box (immobiliser code ECU) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
| *a | Front view of wire harness connector
(to Steering Lock ECU Steering Lock Actuator or Upper Bracket Assembly)) |
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F78-1 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, check for looseness in the ground cable connection.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F78-7 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
| *b | Steering Lock Motor not Operating |
| *c | Steering Lock Motor Operating |
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | F78-3 (IGE) - F78-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor not operating → Operating → Not operating |
When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
In order to take measurements when the lock motor is operating, perform either of the following operations:
To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).
To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
Check for deformation and corrosion of the connector case and terminals.
There is no deformation or corrosion of the connector case or terminals.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F78-3 (IGE) - F1-25 (SLR+) | Always | Below 1 Ω |
| F78-3 (IGE) or F1-25 (SLR+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Reconnect the F1 certification ECU (smart key ECU assembly) connector.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-3 (IGE) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY
Perform registration (refer to Service Bulletin).
Use the Data List to check if L code certification is functioning properly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| L Code Check |
OK is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Perform registration (refer to Service Bulletin).
Use the Data List to check if S code certification is functioning properly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| S Code Check |
OK is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, check the following main body ECU (multiplex network body ECU) Data List item by opening and closing the driver door to confirm the state of the front door courtesy light switch assembly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Front door courtesy light switch assembly RH (for RHD) | ON or OFF | ON: Front door RH open
OFF: Front door RH closed |
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part. |
| FL Door Courtesy SW | Front door courtesy light switch assembly LH (for LHD) | ON or OFF | ON: Front door LH open
OFF: Front door LH closed |
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part. |
| Tester Display |
|---|
| FR Door Courtesy SW |
| FL Door Courtesy SW |
The Data List item changes in accordance with the opening and closing of the driver door.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Move the shift lever to P.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift P Signal | Shift position (P) signal | ON or OFF | ON: Shift lever in P
OFF: Shift lever not in P |
·
Use this item to determine if the shift position switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". |
| Tester Display |
|---|
| Shift P Signal |
ON is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the steering is unlocked.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Lock | State of whether steering lock ECU (steering lock actuator or upper bracket assembly) determined steering is locked | Set or Unset | Set: Steering locked
Unset: Steering unlocked |
If this item displays "Unset", the steering is not locked. |
| Tester Display |
|---|
| Steering Lock |
Set is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Perform registration (refer to Service Bulletin).
Turn the engine switch on (IG).
Use the Data List to check if the steering lock command is functioning properly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Lock Request Receive | Reception state of steering lock request signal by certification ECU (smart key ECU assembly) sent to ID code box (immobiliser code ECU)
|
OK or NG | OK: Lock request received within 10 seconds of opening any door with engine switch off and shift lever in P
NG: Except above |
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Lock Request Receive |
The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to on (ACC) or off and opening a door with the shift lever in P, and OK is displayed on the GTS screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG