Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY › from 2020.08
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294195 FRONT PASSENGER AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the instrument panel passenger airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.


HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 55401E 2.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 73960A 3.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

CAUTION:
B417757C02
0.917,0.938 1.063,1.125 0.146,0.188 10 false .
V100155

Deployment Side


When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.


a.
B454060

Remove the 2 screws.


b.
B454061

Disengage the hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad sub-assembly.

NOTICE:

Do not damage the deployment surface of the instrument panel passenger airbag assembly.



Hide 82142A 4.REMOVE NO. 2 INSTRUMENT PANEL WIRE

a.
B454066C02
1.698,1.885 2.292,1.677 true 0.802,0.667 1.333,1 true 1.531,1.927 0.917,2.833 true 0.667,1.604 1.073,1.76 true 0.719,2.729 1.031,2.885 0.313,0.156 10 false *a 1.406,0.896 1.719,1.052 0.313,0.156 10 false *c 2.365,1.583 2.677,1.74 0.313,0.156 10 false *b 0.479,1.479 0.792,1.635 0.313,0.156 10 false *d
*a Protective Tape
*b Airbag Connector
*c Airbag Connector Lock
*d for TMMT Made Only


Disengage the clamp (for TMMT Made).


b.

Using a screwdriver with its tip wrapped in protective tape, release the airbag connector lock.


c.

Disconnect the airbag connector to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.