Home › Engine / Hybrid System › 3ZR-FAE (FUEL) › FUEL TANK › from 2020.08
RM32H0E _51 Engine / Hybrid System _060184 3ZR-FAE FUEL _0295036 FUEL TANK A

3ZR-FAE FUEL  FUEL TANK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

Because the weight of the fuel tank sub-assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the components could fall down.

·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Simple intelligent parking assist system*1 Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 2.DRAIN FUEL

Hide 17430 3.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Hide 77641A 4.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A393593

Remove the nut, 4 clips and No. 1 fuel tank protector from the fuel tank assembly.


Hide 77754B 5.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A393792

Slide the hose clip and disconnect the charcoal canister outlet hose from the fuel tank filler pipe sub-assembly.


Hide 6.DISCONNECT FUEL TANK BREATHER TUBE

a.
A393793

Disconnect the fuel tank breather tube from the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77213E 7.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A393794

Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77026A 8.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A396125

Slide the clip and disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209F 9.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A396124

Disconnect the fuel tank main tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77100 10.REMOVE FUEL TANK ASSEMBLY

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.
A393797

Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.
A393798

Remove the 4 bolts and 2 fuel tank band sub-assemblies.


c.

Lower the engine lifter to remove the fuel tank assembly.

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




Hide 77651A 11.REMOVE NO. 1 FUEL TANK CUSHION

A393599

a.

Remove the 2 No. 1 fuel tank cushions from the fuel tank assembly.


Hide 77026A 12.REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A393789

Disengage the 4 clamps to remove the No. 1 fuel evaporation tube sub-assembly from the fuel tank assembly.


Hide 77209F 13.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A393790

Disengage the 3 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 77754B 14.REMOVE CHARCOAL CANISTER OUTLET HOSE

a.
A393791

Disengage the 2 clamps to remove the charcoal canister outlet hose from the fuel tank assembly.