Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2020.08
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0292816 REAR CRANKSHAFT OIL SEAL A

3ZR-FAE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear engine oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Simple intelligent parking assist system*1 Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 32101B 2.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, place the engine assembly horizontally.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A234914N20
1.365,2.25 0.74,2.74 0.74,2.74 2.365,3 true 0.438,2.667 1.031,3 0.594,0.333 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-54015  (91551-00850)
09330-00021  


c.
A319942

Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly and front drive plate spacer from the crankshaft.


Hide 11401L 3.REMOVE REAR ENGINE OIL SEAL

a.
A154925C10
0.823,0.406 0.979,0.406 0.979,0.406 0.833,1.365 false 2.844,0.458 2.594,0.458 2.594,0.458 2.031,1.333 true 0.646,0.354 0.906,0.656 0.26,0.302 10 *b 2.865,0.385 3.219,0.635 0.354,0.25 10 *a
*a Protective Tape
*b Cut Position


Using a knife, cut off the rear engine oil seal lip.


b.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

After removal, check the crankshaft for damage. If damaged, smooth the surface with 400-grit sandpaper.


HINT:

Tape the screwdriver tip before use.