The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the horn button assembly removal/installation are shown below.
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The following procedure is for LHD vehicles.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 8NR-FTS:
for 3ZR-FAE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an SRS part is accidentally deployed, it may cause a serious injury.
45130
3.REMOVE HORN BUTTON ASSEMBLY
|
Deployment Side |
When storing the horn button assembly, keep the airbag deployment side facing upward.
Check that the ignition switch off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Turn the steering wheel assembly 180° to the right.
| *a | 55 mm (2.17 in.) |
| *b | 95 mm (3.74 in.) |
|
Protective Tape |
Wrap protective tape around a 6 mm hexagon wrench as shown in the illustration.
Use a 6 mm hexagon wrench with a long arm length of approximately 95 mm (3.74 in.) or a Phillips (+) screwdriver with a shank length of approximately 75 mm (2.95 in.).
Insert the 6 mm hexagon wrench into the service hole until the protective tape is at the position shown in the illustration, and push down the housing tab to disengage the hook.
| *a | Housing Tab | *b | Hook |
|
Protective Tape | - | - |
Make sure to insert the 6 mm hexagon wrench into the service hole on the backside of the steering wheel assembly.
Insert the 6 mm hexagon wrench parallel to the steering column.
Turn the steering wheel assembly 90° to the left.
Insert the 6 mm hexagon wrench into the service hole until the protective tape is at the position shown in the illustration, and push down the housing tab to disengage the hook (1).
| *a | Housing Tab | *b | Hook (1) |
|
Protective Tape | - | - |
Make sure to insert the 6 mm hexagon wrench into the service hole on the backside of the steering wheel assembly.
Insert the 6 mm hexagon wrench parallel to the steering column.
After using the 6 mm hexagon wrench to disengage the hook (1), push down the housing tab further to disengage the hook (2) as shown in the illustration.
| *a | Housing Tab | *b | Omega Spring |
| *c | Hook (1) | *d | Hook (2) |
Pushing down the housing tab will push the omega spring and disengage it from the hook (2).
| a | 10 mm |
When the hook (2) has been disengaged, the horn button assembly will rise up approximately 10 mm.
Turn the steering wheel assembly 180° to the right.
Insert the 6 mm hexagon wrench into the service hole until the protective tape is at the position shown in the illustration, and push down the housing tab to disengage the hook (1).
| *a | Housing Tab | *b | Hook (1) |
|
Protective Tape | - | - |
Make sure to insert the 6 mm hexagon wrench into the service hole on the backside of the steering wheel assembly.
Insert the 6 mm hexagon wrench parallel to the steering column.
After using the 6 mm hexagon wrench to disengage the hook (1), push down the housing tab further to disengage the hook (2) as shown in the illustration.
| *a | Housing Tab | *b | Omega Spring |
| *c | Hook (1) | *d | Hook (2) |
Lightly hold the horn button assembly so that it does not fall.
Pushing down the housing tab will push the omega spring and disengage it from the hook (2).
| a | 10 mm |
When the hook (2) has been disengaged, the horn button assembly will rise up approximately 10 mm.
| *a | Spring |
Check that each hook is disengaged.
If a hook is disengaged, the spring will be visible at the location shown in the illustration.
Turn the steering wheel assembly 180° to the left to align the front wheels facing straight ahead.
Do not drop the horn button assembly.
Pull out the horn button assembly from the steering wheel assembly and hold the horn button assembly with one hand.
When separating the horn button assembly, do not pull the airbag wire harness.
for Single Type:
| *a | Airbag Connector |
| *b | Horn Connector |
| *c | Airbag Connector Lock |
| *d | Protective Tape |
| *e | Wire Harness Clamp |
Disconnect the horn connector from the horn button assembly.
Using a screwdriver with its tip wrapped in protective tape, release the airbag connector lock.
Disconnect the airbag connector.
Disengage the wire harness clamp to remove the horn button assembly
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
for Dual Type:
| *a | Airbag Connector |
| *b | Horn Connector |
| *c | Airbag Connector Lock |
| *d | Protective Tape |
| *e | Wire Harness Clamp |
Disconnect the horn connector from the horn button assembly.
Using a screwdriver with its tip wrapped in protective tape, release the 2 airbag connector locks.
Disconnect the 2 airbag connectors.
Disengage the wire harness clamp to remove the horn button assembly
When disconnecting any airbag connector, take care not to damage the airbag wire harness.