Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE UNIT › from 2020.08
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0295676 MANUAL TRANSAXLE UNIT A

EC6A MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 33101A 1.REMOVE MANUAL TRANSMISSION FILLER PLUG

a.
C194601

Remove the manual transmission filler plug and gasket from the manual transmission case.


Hide 33101B 2.REMOVE MANUAL TRANSMISSION DRAIN PLUG

a.
C194602

Using a 10 mm hexagon socket wrench, remove the manual transmission drain plug and gasket from the front transaxle case.


Hide 3.REMOVE TRANSMISSION REVOLUTION SENSOR

a.
C368124

Remove the bolt, transmission revolution sensor from the manual transmission case.

NOTICE:

If the O-ring is damaged, replace the transmission revolution sensor with a new one.



Hide 84210 4.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
C194603

Using a 27 mm deep socket wrench, remove the back-up light switch assembly and gasket from the manual transmission case.


Hide 5.REMOVE NEUTRAL POSITION SWITCH

a.
C194604

Using a 27 mm deep socket wrench, remove the neutral position switch and gasket from the manual transmission case.


Hide 335A0 6.REMOVE CONTROL CABLE BRACKET ASSEMBLY

a.
C276945

Remove the 3 bolts and control cable bracket assembly from the manual transmission case.


Hide 7.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C368125

Remove the bolt and wire harness clamp bracket from the manual transmission case.


Hide 31121 8.REMOVE NO. 1 CLUTCH HOUSING COVER

a.
C194612

Remove the No. 1 clutch housing cover from the front transaxle case.


Hide 31478 9.REMOVE RELEASE CYLINDER BLEEDER PLUG CAP

a.

Remove the release cylinder bleeder plug cap from the release cylinder bleeder plug.


Hide 10.REMOVE RELEASE CYLINDER BLEEDER PLUG

a.

Remove the release cylinder bleeder plug from the clutch release bleeder sub-assembly.


Hide 31407B 11.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31400 12.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 31483 13.REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE

Hide 14.SECURE MANUAL TRANSAXLE ASSEMBLY

a.
C194619C07
1.01,1.948 0.677,1.948 false 2.302,1.927 2.583,1.927 false 0.521,1.865 0.813,2.063 0.292,0.198 10 false *a 2.615,1.844 3.021,2.042 0.406,0.198 10 false *a
*a Wooden Block


Place the manual transaxle assembly on wooden blocks.


Hide 15.REMOVE TRANSMISSION CASE PLUG

a.
C194614

Remove the transmission case plug and gasket from the manual transmission case.


Hide 33290 16.REMOVE NO. 1 LOCK BALL ASSEMBLY

a.
C194615

Remove the No. 1 lock ball assembly from the manual transmission case.


Hide 33451H 17.REMOVE REVERSE IDLER GEAR SHAFT BOLT

a.
C194616

Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.


Hide 33292A 18.REMOVE LOCK BALL PIN

a.
C194617

Using a 10 mm hexagon socket wrench, remove the shift and select lever shaft straight screw with head plug from the manual transmission case.


b.

Using a Magnet Hand, remove the shift and select lever shaft compression spring and lock ball pin from the manual transmission case.


Hide 33275C 19.REMOVE SHIFT DETENT BALL

a.
C194618

Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the manual transmission case.


b.

Using a Magnet Hand, remove the shift detent ball compression spring and shift detent ball from the manual transmission case.


c.
C194778

Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the manual transmission case.


d.

Using a Magnet Hand, remove the 2 shift detent ball compression springs and 2 shift detent balls from the manual transmission case.


Hide 33253F 20.REMOVE OUTER SHIFT LEVER E-RING

a.
C194622

Remove the outer shift lever E-ring from the outer No. 1 shift lever.


Hide 33111 21.REMOVE MANUAL TRANSMISSION CASE

a.
C194620

Remove the 16 bolts.


b.
C194621C06
0.948,3.135 0.948,2.708 true 0.896,3.156 1.219,3.354 0.323,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, separate the manual transmission case from the front transaxle case.

NOTICE:

Do not damage the manual transmission case.



c.
C194623C01
1.646,2.042 0.948,3.021 0.948,3.021 0.792,3.021 false 0.625,2.958 1.042,3.177 0.417,0.219 10 *a
*a Boss


Turn the outer No. 1 shift lever clockwise until it comes into contact with the boss.


d.
C194624

Push the outer No. 1 shift lever and remove the manual transmission case.


Hide 33402 22.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C194626

Remove the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft from the front transaxle case.


Hide 23.REMOVE REVERSE SHIFT FORK SHAFT ASSEMBLY

a.
C194627

Turn the reverse shift fork shaft assembly clockwise and remove it from the front transaxle case.


Hide 24.REMOVE REVERSE SHIFT FORK

a.

Secure the No. 4 gear shift fork shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C325135

Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the reverse shift fork.


c.
C325136

Remove the reverse shift fork from the No. 4 gear shift fork shaft.


Hide 33240 25.REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY

a.
C194628

Remove the 2 bolts and reverse shift arm bracket assembly from the front transaxle case.


Hide 26.REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY

a.
C194629

Using a 6 mm hexagon socket wrench, remove the inner select lever set bolt.


b.
C194630C01
1.896,3.021 2.594,3.021 true 1.844,3.729 2.906,3.729 true 2.677,2.948 2.99,3.146 0.313,0.198 10 false *1 2.969,3.646 3.281,3.844 0.313,0.198 10 false *2
*1 Shift and Select Lever Shaft Assembly
*2 Shift Inter Lock Plate


Turn the shift and select lever shaft assembly clockwise and remove it from the front transaxle case.


c.

Remove the shift inter lock plate from the front transaxle case.


Hide 33257 27.REMOVE OUTER SELECT LEVER

a.
C194631C04
0.844,1.375 0.844,1.104 true 0.792,1.396 1.25,1.604 0.458,0.208 10 false *a
*a Mark


Remove the outer select lever and inner select lever from the front transaxle case.


Hide 33257C 28.REMOVE OUTER SELECT LEVER OIL SEAL

a.
C194642C04
1.573,1.458 1.844,1.458 false 1.875,1.365 2.125,1.573 0.25,0.208 10 *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the outer select lever oil seal from the front transaxle case.

NOTICE:

Do not damage the installation surfaces.



Hide 29.REMOVE INPUT SHAFT ASSEMBLY

a.
C194632

Remove the input shaft assembly, output shaft assembly, No. 1 gear shift fork shaft assembly, No. 2 gear shift fork shaft assembly and No. 3 gear shift fork shaft assembly from the front transaxle case.


Hide 30.REMOVE NO. 1 GEAR SHIFT HEAD

a.

Secure the No. 1 gear shift fork assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C325108

Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the No. 1 gear shift head.


c.
C325109

Remove the No. 1 gear shift head from the No. 1 gear shift fork assembly.


Hide 31.REMOVE NO. 2 GEAR SHIFT HEAD

a.

Secure the No. 2 gear shift fork assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C325117

Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the No. 2 gear shift head.


c.
C325118

Remove the No. 2 gear shift head from the No. 2 gear shift fork assembly.


Hide 32.REMOVE NO. 2 REVERSE PRE-BALK HEAD

a.
C325119C01
0.854,0.75 1,0.75 1,0.75 1.219,1.104 false 1.354,1.198 1.792,1.115 1.792,1.115 1.552,1.26 true 2.177,0.646 2.26,0.646 2.26,0.646 2.344,0.479 true 0.688,0.667 0.948,0.927 0.26,0.26 10 false *1 1.823,0.979 2.125,1.26 0.302,0.281 10 false *a 2.01,0.563 2.271,0.823 0.26,0.26 10 false *1
*1 Snap Ring
*a Protective Tape


Using 2 screwdrivers with their tips wrapped with protective tape and a hammer, remove the snap ring from the No. 2 gear shift fork assembly.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
C325120

Remove the spacer from the No. 2 gear shift fork assembly.


c.
C325121

Remove the No. 2 reverse pre-balk head from the No. 2 gear shift fork assembly.


d.

Secure the No. 2 reverse pre-balk head in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
C325122

Using a 3 mm pin punch and a hammer, remove the straight pin from the No. 2 reverse pre-balk head.


f.
C325123C02
1.25,1.802 0.958,2.125 0.958,2.125 0.875,2.125 true 2.906,0.948 2.781,0.948 2.781,0.948 2.656,1.365 true 2.198,3.354 2.292,3.354 2.292,3.354 2.448,3.75 true 1.26,4.125 0.792,4.438 0.792,4.438 0.708,4.438 true 2.958,0.875 3.24,1.135 0.281,0.26 10 false *1 0.531,4.333 0.771,4.521 0.24,0.188 10 false *a 2.031,3.271 2.313,3.531 0.281,0.26 10 false *1 0.698,2.01 0.938,2.198 0.24,0.188 10 false *a
*1 Bimetal Formed Bushing
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape and a hammer, remove the 2 bimetal formed bushings from the No. 2 reverse pre-balk head.

NOTICE:

Do not damage the No. 2 reverse pre-balk head.



Hide 33.REMOVE SHIFT LEVER STOPPER

a.
C325125

Remove the torsion spring from the No. 2 gear shift fork assembly.


b.
C325126

Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the shift lever stopper.


c.
C325127

Remove the shift lever stopper from the No. 2 gear shift fork assembly.


Hide 34.REMOVE NO. 3 GEAR SHIFT HEAD

a.

Secure the No. 3 gear shift fork assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C325111

Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the No. 3 gear shift head.


c.
C325112

Remove the No. 3 gear shift head from the No. 3 gear shift fork assembly.


Hide 35.REMOVE NO. 3 REVERSE PRE-BALK HEAD

a.
C325114

Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the No. 3 reverse pre-balk head.


b.
C325115

Remove the No. 3 reverse pre-balk head from the No. 3 gear shift fork assembly.


Hide 36.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C194633

Remove the differential case assembly from the front transaxle case.


Hide 41311E 37.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C194639N03
2.479,1 2.771,1 false 1.167,0.823 1.271,0.823 false 2.792,0.927 3.146,1.135 0.354,0.208 10 SST 1.302,0.75 1.656,0.958 0.354,0.208 10 SST

Using SST, remove the front differential case front tapered roller bearing (outer race) and front differential case front plate washer from the front transaxle case.

SST
09308-00010  


b.
C193754C04
1.865,1.75 2.813,1.75 2.813,1.75 2.49,1.563 false 1.729,3.594 2.031,3.594 2.031,3.594 1.51,3.979 false 2.865,1.677 3.208,1.875 0.344,0.198 10 SST 2.938,0.24 3.302,0.448 0.365,0.208 10 *b 0.417,1.292 0.771,1.5 0.354,0.208 10 *a 2.073,3.51 2.417,3.708 0.344,0.198 10 SST
*a Hold
*b Turn


Using SST, remove the front differential case front tapered roller bearing (inner race) from the differential case assembly.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00390)


Hide 41311F 38.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C194651N03
0.948,1.188 0.594,1.188 false 2.813,0.427 2.969,0.427 false 0.302,1.115 0.677,1.333 0.375,0.219 10 SST 2.979,0.354 3.313,0.594 0.333,0.24 10 SST

Using SST, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear plate washer from the manual transmission case.

SST
09308-00010  


b.
C193753C04
2.083,1.094 2.573,1.094 2.573,1.094 1.906,1.594 false 1.771,3.5 2.063,3.5 2.063,3.5 1.552,3.885 false 2.625,1 2.969,1.229 0.344,0.229 10 SST 2.115,3.396 2.458,3.625 0.344,0.229 10 SST 2.313,0.292 2.74,0.552 0.427,0.26 10 *b 0.229,0.844 0.604,1.052 0.375,0.208 10 *a
*a Hold
*b Turn


Using SST, remove the front differential case rear tapered roller bearing (inner race) from the differential case assembly.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00390)


Hide 33449B 39.REMOVE TRANSMISSION MAGNET

a.
C194634

Remove the transmission magnet from the front transaxle case.


Hide 33176B 40.REMOVE TRANSMISSION OIL SEPARATOR

a.
C194635

Remove the 4 bolts and transmission oil separator from the front transaxle case.


Hide 33101J 41.REMOVE BREATHER PLUG

a.
C194636

Remove the breather plug from the front transaxle case.


Hide 33321N 42.REMOVE FRONT OUTPUT SHAFT BEARING (OUTER RACE)

a.
C194637N03
1.313,0.958 1.635,0.958 false 2.167,2.094 2.281,2.094 false 1.656,0.875 2.188,1.146 0.531,0.271 10 SST 1.885,2.021 2.229,2.229 0.344,0.208 10 SST

Using SST, remove the front output shaft bearing (outer race) from the front transaxle case.

SST
09308-00010  


b.
C194638

Remove the output shaft cover from the front transaxle case.


Hide 31105D 43.REMOVE FRONT TRANSAXLE CASE OIL SEAL

a.
C194641N03
1.135,0.958 0.479,0.906 0.479,0.906 1.083,1.792 false 2.406,1.5 2.188,1.5 2.188,1.5 2.323,1.833 false 0.177,0.833 0.542,1.031 0.365,0.198 10 SST 1.906,1.427 2.271,1.625 0.365,0.198 10 SST

Using SST and a hammer, remove the front transaxle case oil seal from the front transaxle case.

SST
09950-60010  (09951-00360)
09950-70010  (09951-07150)


Hide 44.REMOVE REVERSE RESTRICT PIN ASSEMBLY

a.
C195992

Remove the reverse restrict pin assembly from the front transaxle case.


Hide 45.REMOVE STRAIGHT PIN

a.
C202594

Remove the 5 straight pins from the front transaxle case.


Hide 33311K 46.REMOVE REAR INPUT SHAFT BEARING SHIM

a.
C194644

Remove the rear input shaft bearing shim from the manual transmission case.


Hide 33137 47.REMOVE INPUT SHAFT COVER

a.
A295612

Remove the input shaft cover from the manual transmission case.


Hide 33124C 48.REMOVE NO. 1 OIL RECEIVER PIPE

a.
C368152

Remove the No. 1 oil receiver pipe from the manual transmission case.


Hide 33176B 49.REMOVE TRANSMISSION OIL SEPARATOR

a.
C194647

Remove the 2 bolts and transmission oil separator from the manual transmission case.


Hide 33109C 50.REMOVE MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY

a.
C416337

Remove the 3 bolts and manual transmission oil separator sub-assembly from the manual transmission case.


Hide 33253 51.REMOVE OUTER NO. 1 SHIFT LEVER

a.
C197467

Using a 5 mm pin punch and a hammer, remove the inner shift lever slotted spring pin from the inner No. 1 shift lever.

HINT:

When removing the inner shift lever slotted spring pin, align the inner shift lever slotted spring pin with the hole in the No. 1 lock ball assembly.



b.

Remove the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever from the manual transmission case.


Hide 33253H 52.REMOVE OUTER SHIFT LEVER OIL SEAL

a.
C194653C04
1.5,1.531 1.083,0.146 1.083,0.146 0.833,0.146 true 0.677,0.073 1,0.396 0.323,0.323 10 *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the outer shift lever oil seal from the manual transmission case.

NOTICE:

Do not damage the installation surfaces.



Hide 33321A 53.REMOVE REAR OUTPUT SHAFT BEARING (OUTER RACE)

a.
C194650N03
0.979,0.323 0.698,0.323 false 2.302,0.375 1.885,0.375 false 0.417,0.24 0.885,0.49 0.469,0.25 10 SST 1.594,0.292 2.063,0.542 0.469,0.25 10 SST

Using SST, remove the rear output shaft bearing (outer race) and rear output shaft bearing shim from the manual transmission case.

SST
09308-00010  


Hide 43420H 54.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C194652N03
1.115,0.771 0.427,0.771 0.427,0.771 1,1.958 false 2.51,2.031 2.344,2.031 2.344,2.031 2.438,2.354 false 0.125,0.688 0.792,0.969 0.667,0.281 10 SST 2.063,1.948 2.385,2.135 0.323,0.188 10 SST

Using SST and a hammer, remove the front drive shaft oil seal LH from the manual transmission case.

SST
09950-60010  (09951-00620)
09950-70010  (09951-07150)


Hide 43410M 55.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C201402N03
1.208,1.49 0.594,1.302 0.594,1.302 1.125,2.406 false 2.406,2.167 2.24,2.167 2.24,2.167 2.313,2.573 false 0.302,1.208 0.771,1.49 0.469,0.281 10 SST 1.958,2.083 2.427,2.365 0.469,0.281 10 SST

Using SST and a hammer, remove the front drive shaft oil seal RH from the front transaxle case.

SST
09950-60010  (09951-00530)
09950-70010  (09951-07150)