Based on the signal received by the shift solenoid valve SL, the ECM uses the shift solenoid valve SLU to control the lock-up clutch pressure.
If there is an open or short in the shift solenoid valve SL circuit, the ECM stops sending current to the malfunctioning shift solenoid valve.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P074011 | Torque Converter Clutch Circuit Short to Ground | While the lock-up is operating, a short is detected in the shift solenoid valve SL circuit 1 time or more consecutively (1 trip detection logic). | ·
Wire harness or connector ·
Continuously variable transaxle assembly (Shift solenoid valve SL) ·
ECM |
Comes on | DTC stored | SAE Code:
P2769 |
| P074015 | Torque Converter Clutch Circuit Short to Battery or Open | While the lock-up is operating, an open is detected in the shift solenoid valve SL circuit 1 time or more consecutively (1 trip detection logic). | ·
Wire harness or connector ·
Continuously variable transaxle assembly (Shift solenoid valve SL) ·
ECM |
Comes on | DTC stored | SAE Code:
P2770 |
These DTCs indicate an open or short in the shift solenoid valve SL circuit. If there is an open or short in the shift solenoid valve SL circuit, the ECM detects the malfunction, illuminates the MIL and stores a DTC.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Drive the vehicle and confirm the lock-up on and off conditions according to Road Test.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Check for DTCs again.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for TMMF Made | A |
| for TMC Made | B |
A
B
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C40 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SL) - Body ground | 20°C (68°F) | 11 to 15 Ω |
Connect the C40 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C62-75 (SL) - Body ground | 20°C (68°F) | 11 to 15 Ω |
Connect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the continuously variable transaxle assembly.
When Not Using the Engine Support Bridge
When Using the Engine Support Bridge
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C40 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SL) - Body ground | 20°C (68°F) | 11 to 15 Ω |
Connect the C40 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C74-75 (SL) - Body ground | 20°C (68°F) | 11 to 15 Ω |
Connect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the continuously variable transaxle assembly.
When Not Using the Engine Support Bridge
When Using the Engine Support Bridge
| Proceed to |
|---|
| NEXT |
NEXT