According to current from the ECM, the shift solenoid valve SLS controls secondary pulley pressure and belt clamping pressure in accordance with the input shaft torque.
| *1 | Spool Valve | *2 | Sleeve |
| *3 | Solenoid Coil | - | - |
| *a | Hydraulic Pressure | *b | Current Flow to Solenoid |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P282813 | Pressure Control Solenoid "K" Circuit Open | While the vehicle is driven, an open or a short is detected in the shift solenoid valve SLS circuit for 1 second or more (1 trip detection logic). | ·
Wire harness or connector ·
Continuously variable transaxle assembly (Shift solenoid valve SLS) ·
ECM |
Comes on | DTC stored | SAE Code:
P282B |
This DTC indicates an open or short in the shift solenoid valve SLS circuit. If there is an open or short in the shift solenoid valve SLS circuit, the ECM detects the malfunction, illuminates the MIL and stores this DTC.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform the D position test in Road Test.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Check for DTCs again.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for TMMF Made | A |
| for TMC Made | B |
A
B
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C40 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (SLS+) - 12 (SLS-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| 5 (SLS+) - Body ground and other terminals | Always | 10 kΩ or higher |
| 12 (SLS-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C40 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C62-1 (SLS+) - C62-31 (SLS-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C62-1 (SLS+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-31 (SLS-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the continuously variable transaxle assembly.
When Not Using the Engine Support Bridge
When Using the Engine Support Bridge
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C40 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (SLS+) - 12 (SLS-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| 5 (SLS+) - Body ground and other terminals | Always | 10 kΩ or higher |
| 12 (SLS-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C40 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C74-1 (SLS+) - C74-31 (SLS-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C74-1 (SLS+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C74-31 (SLS-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the continuously variable transaxle assembly.
When Not Using the Engine Support Bridge
When Using the Engine Support Bridge
| Proceed to |
|---|
| NEXT |
NEXT