The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. The next time the engine is started, the ECM will illuminate the MIL and store this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P056014 | System Voltage Circuit Short to Ground or Open | An open or short in the ECM backup power source circuit (1 trip detection logic). | ·
Open or short in backup power source circuit ·
Battery ·
Battery terminals ·
ECM |
Comes on | DTC stored | SAE Code:
P0562 |
| Required Sensors/Components | ECM |
| Frequency of Operation | Continuous |
| Both of the following conditions are met | - |
| Battery voltage (BATT) | Below 3.5 V |
| Electronic throttle actuator power supply voltage (+BM) | Below 3.5 V |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Wait 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P056014.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Inspect the fuses for circuits related to this system before performing the following procedure.
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Inspect the battery.
Click herePower Source / Network>8NR-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
Battery voltage is between 11 to 14 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the battery terminals are not loose or corroded.
Click herePower Source / Network>8NR-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
Battery terminals are not loose or corroded.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
| *A | for TMMT Made | *B | for TMC Made |
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-1 (BATT) - Body ground | Always | 11 to 14 V |
| C62-48 (+BM) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-1 (BATT) - Body ground | Always | 11 to 14 V |
| C74-48 (+BM) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Wait 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P056014 is output | A |
| DTCs are not output | B |
A
B
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS