The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly and door side airbag sensor RH.
The door side airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the door side airbag sensor RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B166C | Front Door Pressure Sensor RH | ·
Door side airbag sensor RH malfunction ·
Airbag sensor assembly malfunction |
·
Door side airbag sensor RH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| B166F | Front Door Pressure Sensor Threshold Malfunction (RH) | ·
Door side airbag sensor RH malfunction ·
Airbag sensor assembly malfunction |
·
Door side airbag sensor RH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ |
| Malfunction Status | Door side airbag sensor RH malfunction | ○ | - |
| Airbag sensor assembly malfunction | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ |
| Malfunction Status | Door side airbag sensor RH malfunction | ○ | - |
| Airbag sensor assembly malfunction | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| *1 | Door Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Interchange the door side airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Codes other than DTCs B166C, B166F, B167A and B167E may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B166C or B166F is output. | A |
| DTC B167A or B167E is output. | B |
| DTCs B166C, B166F, B167A and B167E are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING