2006-2011 Camry Aurion · Service Manual SECURITIES

B2799 Engine Immobiliser System Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This DTC is output when one of the following occurs: 1) the ECM detects errors in its own communications with the ID code box; 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the ID code box and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no certification ECU DTCs are present. If present, troubleshoot the certification ECU DTCs first.
DTC No.
DTC Detection Condition
Trouble Area
B2799
One of following conditions is met:
  1. Error in communication between ECM and ID code box
  2. Error in communication lines
  3. Communication ID is different between ID code box and ECM during communication
  1. Wire harness
  2. ECM
  3. ID code box

WIRING DIAGRAM

B150860E02

INSPECTION PROCEDURE

NOTICE:
  1. If the ID code box is replaced, register the key and ECU communication ID.
  2. If the ECM is replaced, register the ECU communication ID.


1. CHECK DTC OUTPUT
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    Result:
    Result
    Proceed to
    B2799 output recurs
    A
    B2799 output does not recur
    B



B
USE SIMULATION METHOD TO CHECK
A


2. RE-REGISTER ECU COMMUNICATION ID
  1. Re-register the ECU communication ID between the ID code box and ECM.

  1. Check that the engine starts.

    OK:
    The engine starts.



OK
END
NG


3. CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)

  1. Disconnect the E50 ID code box and A55*1 or A24*2 ECM connector.

    HINT:
    *1: for LHD
    *2: for RHD

    B150861E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    E50-5 (EFII) - A55-10 (IMO)
    Below 1 Ω
    E50-6 (EFIO) - A55-11 (IMI)
    E50-5 (EFII) - Body ground
    10 kΩ or higher
    E50-6 (EFIO) - Body ground
    for RHD:
    Tester Connection
    Specified Condition
    E50-5 (EFII) - A24-10 (IMO)
    Below 1 Ω
    E50-6 (EFIO) - A24-11 (IMI)
    E50-5 (EFII) - Body ground
    10 kΩ or higher
    E50-6 (EFIO) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE ECM
  1. Replace the ECM (Click here for 2GR-FE, Click here for 2AZ-FE).


NEXT


5. ECU COMMUNICATION ID REGISTRATION
  1. Register the ECU communication ID between the ID code box and ECM.


NEXT


6. CHECK DTC OUTPUT
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    Result:
    Result
    Proceed to
    B2799 output recurs
    A
    B2799 output does not recur
    B



B
END
A

REPLACE ID CODE BOX


← B2799 Engine Immobiliser System Malfunction (Oct 2006 – May 2009)ID Code Box Power Source Circuit (Oct 2006 – May 2009) →