2006-2011 Camry Aurion · Service Manual TRANSMISSION

REGISTRATION

Other · Vehicles built from Oct 2006

NOTICE:
  1. When the automatic transaxle is replaced, the transaxle's compensation code must be input into the TCM (Proceed to step 1). After the automatic transaxle is reinstalled, the QR code label will be positioned where the code cannot be read. Therefore, before reinstalling the automatic transaxle, record the transaxle compensation codes or input them in the intelligent tester.
  2. When the TCM is replaced, the existing transaxle compensation codes must be input into the new TCM (Proceed to step 2).


1. INPUT TRANSAXLE COMPENSATION CODE INTO TCM

NOTICE:
Transaxle compensation codes are unique, 60-digit alphanumeric values printed on the QR label. If an incorrect transaxle compensation code is input into the TCM, shift shock may occur.

  1. C133268E02
    Record the transmission compensation code specified on the QR label.

    HINT:
    The transaxle compensation code is imprinted on the QR label.

  1. Shift the shift lever to the N or P position.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

    NOTICE:
    Do not start the engine.

  1. C122773
    Enter the menu items in this order: Powertrain / ECT / Utility / A/T Code Registration.

  1. Press "Next".

  1. C122774
    Press "Next" again to proceed.

  1. C122776
    Select "Set Compensation Code".

  1. Press "Next".

  1. C122777
    Register the compensation code.

    1. Press "Input".

    2. A096465
      Manually input the transaxle compensation code. The code is a 60-digit alphanumeric value printed on the QR label. After inputting the code, press "OK".

  1. C122778
    Check that the compensation code displayed on the screen is correct by comparing it with the 60-digit alphanumeric value on the QR label.

    NOTICE:
    If an incorrect transaxle compensation code is input into the TCM, shift shock will occur.

  1. C122800
    Press "Next" to set the compensation code to the TCM.

  1. Press "Exit".


2. TRANSFER TRANSAXLE COMPENSATION CODE

NOTICE:
Transaxle compensation codes are 60-digit alphanumeric values printed on the QR label. If an incorrect transaxle compensation code is input into the TCM, shift shock may occur.

HINT:
The following operation is available for use with TCMs that can transmit the registered transaxle compensation code to the intelligent tester.

  1. Shift the shift lever to the N or P position.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

    NOTICE:
    Do not start the engine.

    HINT:
    The transaxle compensation code is imprinted on the QR label.

  1. Read the transaxle compensation code.

    1. C122773
      Enter the menu items in this order: Powertrain / ECT / Utility / A/T Code Registration.

    2. Press "Next".

    3. C122774
      Press "Next" again to proceed.

    4. C122799
      Select "Read Compensation Code".

    5. Press "Next".

    6. C122801
      Press "Save".

    7. C122789
      C122790
      Press "Save".

      HINT:
      If the code has already been saved, the following screen will be shown.
      Press "Overwrite".

      NOTICE:
      Do not use the code specified on the transaxle QR label even if the transmission compensation code cannot be read using the intelligent tester. The code printed on an in-service transaxle may not match its current characteristics. Replace the TCM with a new one and perform a road test to allow the TCM to learn.

    8. C122792
      Press "Exit".

    9. Turn the ignition switch off.

  1. Replace the TCM.

  1. Set the transaxle compensation code.

    1. Turn the ignition switch on (IG).

    2. Turn the tester on.

    3. C122773
      Enter the menu items in this order: Powertrain / ECT / Utility / A/T Code Registration.

    4. Press "Next".

    5. C122774
      Press "Next" again to proceed.

    6. C122776
      Select "Set Compensation Code".

    7. Press "Next".

    8. C122777
      Press "Open".

    9. C122779
      Press "Open" again to proceed.

    10. C122803
      Press "Exit".

← MANUAL SHIFTING TEST (from Jun 2009)INITIALIZATION (Oct 2006 – May 2009) →