2006-2011 Camry Aurion · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

CAUTION:
Wear protective gloves. Sharp areas on the seat adjuster may injure your hands.


1. INSTALL SEAT POSITION SENSOR (for Driver Seat)
  1. Check that the ignition switch is off.

  1. Check that the negative battery (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133893E01
    Engage the pin and install the seat position sensor to the seat slide position sensor protector as shown in the illustration.

  1. C107067E08
    Using a 1.0 mm (0.039 in.) feeler gauge, temporarily install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).

  1. C133891
    Using a "TORX" socket (T30), tighten the "TORX" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).

  1. Check that there is no looseness in the installation parts of the seat position sensor.

  1. Connect the connector.


2. INSTALL FRONT SEAT WIRE
  1. Engage the each claw and each clamp and install the front seat wire.


3. INSTALL FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY

  1. B148636
    Install the front separate type seatback spring assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B165296E01
    Connect the 2 clamps and connector.


4. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH

  1. B148633
    Engage the 2 claws.

  1. Install the front lower seat cushion shield LH with the screw.


5. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH

  1. B148634
    Engage the 2 claws.

  1. Install the front lower seat cushion shield RH with the screw.


6. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH

  1. B148632
    Engage the claw.

  1. Install the upper reclining adjuster inside cover LH with the screw.


7. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH

  1. B148631
    Engage the claw.

  1. Install the upper reclining adjuster inside cover RH with the screw.


8. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH

  1. B148630
    Install the lower reclining adjuster inside cover LH with the screw.


9. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH

  1. B146667
    Install the lower reclining adjuster inside cover RH with the screw.


10. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY

  1. B165278
    Install the lumbar support adjuster assembly with the 2 screws.

  1. Connect the connector.


11. INSTALL FRONT SEPARATE TYPE SEATBACK COVER (for Except Sports Seat Type)

  1. B148637E01
    Using hog ring pliers, install the front separate type seatback cover to the front seatback pad with 12 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


12. INSTALL FRONT SEPARATE TYPE SEATBACK COVER (for Sports Seat Type)

  1. B144038E01
    Using hog ring pliers, install the front separate type seatback cover to the front seatback pad with 14 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


13. INSTALL FRONT SEATBACK ASSEMBLY (for Except Sports Seat Type)
  1. Install the front seatback assembly to the front seatback spring assembly.

  1. B165280
    Install the front seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
    2. Make sure that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.

  1. B149612E01
    Engage the 6 hooks.

  1. Using hog ring pliers, install 5 new hog rings.

  1. B165281E01
    Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


14. INSTALL FRONT SEATBACK ASSEMBLY (for Sports Seat Type)

  1. B165280
    Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
    2. Make sure that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.

  1. Engage the 3 hooks.

  1. B165282E01
    Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


15. INSTALL FRONT SEAT HEADREST SUPPORT

  1. B146662
    Engage the 2 claws to install the front seat headrest support.

    HINT:
    Use the same procedure for the RH side and LH side.


16. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for Except Sports Seat Type)

  1. B165275
    Engage the 4 claws.

  1. Install the front seatback board sub-assembly with the 2 screws.


17. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for Sports Seat Type)

  1. B134682E02
    Engage the 2 claws.

  1. Engage the 14 claws.

  1. Install the front seatback board sub-assembly with the 2 screws.


18. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER (for Except Sports Seat Type)

  1. B148639E01
    Using hog ring pliers, install the front separate type seat cushion cover to the front separate type seat pad with 16 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


19. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER (for Sports Seat Type)

  1. B144037E01
    Using hog ring pliers, install the front separate type seat cushion cover to the front separate type seat pad with 17 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


20. INSTALL FRONT SEAT CUSHION ASSEMBLY

  1. B165274E01
    Engage the hooks.

  1. B165273
    Engage the 4 hooks.

  1. Connect the connector.


21. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. for LHD:

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. Connect the connector. (for Driver Seat)

      B151323E01

    3. B151312E01
      Connect the connectors and engage each clamp.

    4. B147624
      Engage the 2 hooks.

  1. for RHD Driver Seat:

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. B236444E01
      Connect the connector.

    3. B151313E03
      Connect the connector and engage each clamp.

    4. B152833
      Engage the 2 hooks.

  1. for RHD Passenger Seat:

    1. B236442E01
      Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. Connect the connector and engage each clamp.

    3. Engage the 2 hooks.


22. INSTALL FRONT INNER SEAT CUSHION SHIELD

  1. B165271
    Engage the 3 claws.

  1. Install the front inner seat cushion shield with the screw.


23. INSTALL POWER SEAT SWITCH

  1. B165272
    Install the power seat switch with the 3 screws.

  1. Connect the connector.


24. INSTALL FRONT POWER SEAT LUMBAR SWITCH

  1. B165270
    Install the front power seat lumbar switch with the 2 screws.


25. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD

  1. B165269
    Engage the 2 claws.

  1. Install the front inner No. 1 seat cushion shield with the 2 screws.


26. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY
  1. Connect the connector.

  1. B147698
    Engage the 2 claws.

  1. Install the front seat cushion shield assembly with the 5 screws.

  1. B146651
    Install the 2 rubber bands on the backside of the front seatback board sub-assembly.


27. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

  1. B147701
    Install the slide and vertical power seat switch knob.


28. INSTALL RECLINING POWER SEAT SWITCH KNOB

  1. B147702
    Install the reclining power seat switch knob.

← REASSEMBLY (Oct 2006 – May 2009)INSTALLATION (Oct 2006 – May 2009) →