2006-2011 Camry Aurion · Service Manual TRANSMISSION

DATA LIST / ACTIVE TEST

System information · Vehicles built from Oct 2006


DATA LIST

HINT:
Using the Data List function of the intelligent tester allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn the tester on.

  6. Enter the following menus: "Powertrain / ECT / Data List".

  7. According to the display on the tester, read "Data List".

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    1. 15.0 to 35.0%: Idling
    2. 10.0 to 30.0%: Running without load (2,000 rpm)
    -
    Engine Speed
    Engine speed:
    Min./ 0 rpm, Max.: 16,383.75 rpm
    550 to 800 rpm: Idling
    -
    Vehicle Speed
    Vehicle speed:
    Min./ 0 km/h, Max.: 255 km/h
    Actual vehicle load
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C (-40°F), Max.: 140°C (284°F)
    80 to 105°C (176 to 221°F): After warming up
    1. If value -40°C (-40°F): sensor circuit open
    2. If value 140°C (284°F): sensor circuit shorted
    Throttle Position
    Throttle position/
    Min.: 0%, Max.: 100%
    10 to 22%: Idling
    Calculated value based on VTA1
    Throttle Position from EFI
    Throttle position/
    Min.: 0%, Max.: 100%
    1. 0%: Accelerator pedal released
    2. 64 to 96%: Accelerator pedal fully depressed
    Recognition valve for throttle opening angle on ECM
    SPD (NC)
    Min.: 0 rpm, Max.: 12,750 rpm
    -
    -
    SPD (NT)
    Input turbine speed/
    Display: 50 r/min

    HINT:
    1. Lock-up ON (After warming up the engine):
      Input turbine speed (NT) equal to the engine speed.
    2. Lock-up OFF (Idling at N position):
      Input turbine speed (NT) nearly equal to the engine speed.

    -
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Starter Signal
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    Shift lever position is;
    P and N: ON
    Except P and N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Stop Light Switch
    Stop light switch status/
    ON or OFF
    1. Brake pedal is depressed: ON
    2. Brake pedal is released: OFF
    -
    Battery Voltage
    Battery voltage/
    Min.: 0, Max.: 65.535 V
    9 to 14 V: Idling
    -
    TC and TE1
    TC and CG terminals of DLC3/
    ON or OFF
    -
    Active Test support data
    Idle Fuel Cut
    Fuel cut idle/
    ON or OFF
    ON: Fuel cut operating
    FC IDL="ON" with the throttle valve fully closed and the engine speed over 2,800 rpm
    FC TAU
    Fuel cut TAU (Fuel cut during very light load)/
    ON or OFF
    ON: Fuel cut operating
    Fuel cut being performed under very light load to prevent incomplete engine combustion.
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th, 5th or 6th
    Shift lever position is;
    D: 1st, 2nd, 3rd, 4th, 5th or 6th
    S: 1st, 2nd, 3rd, 4th, 5th or 6th
    -
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    Shift lever position is;
    R: ON
    Except R: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    Shift lever position is;
    D and S: ON
    Except D and S: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. Press continuously "+" (Up shift): ON
    2. Release "+" (Up shift): OFF
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. Press continuously "-" (Down shift): ON
    2. Release "-" (Down shift): OFF
    -
    Sports Mode selection SW
    Sport mode select switch status/
    ON or OFF
    Shift lever position is;
    S, "+" and "-": ON
    Except S, "+" and "-": OFF
    -
    TPS 1 Switch
    0: OFF / 1: ON
    Gear position 1st, 2nd, 3rd or 4th: ON
    Gear position 5th or 6th: OFF
    -
    TPS 2 Switch
    0: OFF / 1: ON
    Gear position 4th, 5th or 6th: ON
    Gear position 1st, 2nd or 3rd: OFF
    -
    TPS 3 Switch
    0: OFF / 1: ON
    Shift solenoid valve SLU is ON: ON
    Shift solenoid valve SLU is OFF: OFF
    -
    A/T Oil Temperature 1
    ATF temp. sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test;
      Approx. 80°C (176°F)
    2. Equal to ambient temperature when cold soak
    If the value is "-40°C (-40°F)" or "215°C (419°F)", the ATF temp. sensor circuit is open or shorted.
    NT Sensor Voltage
    Min.: 0 V, Max.: 5 V
    0.1 to 1.9 V
    -
    NC Sensor Voltage
    Min.: 0 V, Max.: 5 V
    0.1 to 1.9 V
    -
    AT Fluid
    Flex lockup judder judgement flag /
    0: OFF / 1: ON
    -
    -
    Lock UP
    0: OFF / 1: ON
    Lock up: ON
    -
    Lock UP Solenoid Status
    Lock up solenoid status/
    ON or OFF
    1. Lock up: ON
    2. Except lock up: OFF
    -
    SLU Solenoid Status
    Shift Solenoid SLU status/
    ON or OFF
    1. Lock up: ON
    2. Except lock up: OFF
    -
    SLT Solenoid Status
    Shift solenoid SLT status/
    ON or OFF
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    -
    Intake-Air Temp from EFI
    Intake air temperature/
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    Equivalent to ambient air temperature
    1. If value -40°C (-40°F): sensor circuit open
    2. If value 215°C (419°F): sensor circuit shorted
    Accel Position from EFI
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Accelerator pedal released
    2. 54 to 86%: Accelerator pedal fully depressed
    -
    #Codes
    # of Codes/
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    Check Mode
    Check mode/
    0: OFF, 1: ON
    ON: Check mode ON
    -
    SPD Test
    Check mode result for vehicle speed sensor/
    0: COMPL, 1: INCMPL
    -
    -
    MIL
    MIL status/
    ON or OFF
    ON: MIL ON
    -
    MIL On Run Distance
    MIL ON run distance/
    Min.: 0 km,
    Max.: 65,535 km
    Distance after DTCs are detected
    -
    Running Time from MIL ON
    Running time from MIL ON/
    Min.: 0 minute,
    Max.:65,535 minutes
    Equivalent to running time after MIL turns ON
    -
    Engine Run Time
    Engine run time/
    Min.: 0 second,
    Max.: 65,535 seconds
    Time after engine start
    -
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 minute,
    Max.: 65,535 minutes
    Equivalent to time after DTCs are erased
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km/h,
    Max.: 65,535 km/h
    Equivalent to time after DTCs are erased
    -
    Warmup Cycle Cleared
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTCs are cleared
    OBD Requirements
    OBD requirement
    OBD2
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    0: NOT AVL / 1: AVAIL
    -
    Comprehensive Component Monitor
    Transmission Type
    Transmission type
    -
    Identifying transmission type:
    6 speed
    SYSTEM
    System identification
    -
    Identifying engine type:
    GASOLINE (gasoline engine)


ACTIVE TEST

HINT:
Performing the Active Test using the intelligent tester allows relays, VSVs, actuators and other items to be operated without removing any parts. Performing the Active Test as the first step in troubleshooting is one method to save diagnostic time.
It is possible to display the Data List during the Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following items: "Powertrain / ECT / Active Test".

  7. According to the display on the tester, perform "Active Test".

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operates the shift solenoid valves to allow gears to selected manually.
    [Shift Position]
    0001: 1st / 0010: 2nd / 0011: 3rd / 0100: 4th / 0101: 5th / 0110: 6th
    Can be used to check the operation of the shift solenoid valves.
    Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
    Do not downshift at high speeds. Doing so will damage the automatic transaxle.
    [Vehicle Condition]
    1. 50 km/h (30 mph) or less
    Activate the Solenoid (SL1)
    Operates shift solenoid SL1
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL2)
    Operates shift solenoid SL2
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL3)
    Operates shift solenoid SL3
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL4)
    Operates shift solenoid SL4
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Lock Up
    Controls the shift solenoid SLU and SL to set the automatic transaxle to the lock-up condition.
    ON/OFF
    Can be used to check SLU and SL solenoid operation.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 20%
    2. Vehicle speed:60 km/h (37 mph) or more, and 6th gear
    Activate the Solenoid (SL)
    Operates shift solenoid SL
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SLU)
    Operates shift solenoid SLU
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SLT)*
    Operates shift solenoid SLT to raise the line pressure.
    ON/OFF

    HINT:
    ON: No action (normal operation)
    OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the TCM commands the SLT solenoid to turn off).

    [Vehicle Condition]
    1. Vehicle Stopped
    2. IDL: ON
    Connect the TC and TE1
    Connects and disconnects TC and TE1.
    (transitions into the fluid temperature detection mode)
    ON/OFF
    The MIL will not blink when "Connect the TC and TE1 / ON" is selected.
    *: "Activate the Solenoid (SLT)" in the Active Test is performed to check the line pressure changes by connecting the SST to the automatic transaxle. The same SST is used for the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in Active Test and HYDRAULIC TEST will be different from each other.

← FAIL-SAFE CHART (from Oct 2006)DIAGNOSTIC TROUBLE CODE CHART (Oct 2006 – May 2009) →