Park / Neutral Position Switch Circuit
Circuit diagnosis · Vehicles built from Oct 2006
DESCRIPTION
The park/neutral position switch detects the shift lever position and sends signals to the TCM.WIRING DIAGRAM


INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- According to the Data List displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the Data List as the first step in troubleshooting is one method to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Enter the following items: "Powertrain / ECT / Data List".
According to the display on the tester, read "Data List".
Item
Measurement Item/
Range (display)
Normal Condition
Diagnostic Note
Neutral Position SW Signal
PNP Switch Status/
ON or OFF
Shift lever position is;
P and N: ON
Except P and N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW Status (R Range)
PNP Switch Status/
ON or OFF
Shift lever position is;
R: ON
Except R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW Status (D Range)
PNP Switch Status/
ON or OFF
Shift lever position is;
D and S: ON
Except D and S: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
| 1. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Disconnect the park/neutral position switch connector.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
- Standard resistance:
Shift Position
Tester Connection
Specified Condition
P
RB (C1-1) - PL (C1-3) and B (C1-4) - L (C1-9)
Below 1 Ω
Except P
10 kΩ or higher
R
RB (C1-1) - RL (C1-2)
Below 1 Ω
Except R
10 kΩ or higher
N
RB (C1-1) - NL (C1-8) and B (C1-4) - L (C1-9)
Below 1 Ω
Except N
10 kΩ or higher
D, S, "+" and "-"
RB (C1-1) - DL (C1-7)
Below 1 Ω
Except D, S, "+" and "-"
10 kΩ or higher
|
|
||||
| OK | |
| 2. INSPECT TRANSMISSION CONTROL SWITCH |
Connect the park/neutral position switch connector.

Disconnect the transmission control switch connector of the shift lock control unit assembly.
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
- Standard resistance:
Shift Position
Tester Connection
Specified Condition
S, "+" and "-"
E31-3 - E31-7
Below 1 Ω
Except S, "+" and "-"
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK ECU TERMINAL VOLTAGE (STA TERMINAL) |
Connect the transmission control switch connector of the shift lock control unit assembly.

Measure the voltage according to the value(s) in the table below while cranking the engine.
- Standard voltage:
Tester Connection
Specified Condition
STA (C56-10) - Body ground
9 to 14 V
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM) |
Disconnect the TCM connector.

Turn the ignition switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
- Standard voltage:
Shift Position
Tester Connection
Specified Condition
R
R (C56-15) - Body ground
10 to 14 V *
Except R
Below 1 V
D
D (C56-16) - Body ground
10 to 14 V
Except D
Below 1 V
- HINT:
- *: The voltage will drop slightly because the back up light is turned on.
|
|
||||
| OK | ||
| ||
