2006-2011 Camry Aurion · Service Manual TRANSMISSION

P0711 Transmission Fluid Temperature Sensor "A" Performance

Diagnostic trouble codes · Vehicles built from Oct 2006

DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value for use by the TCM.
G031389E14
The TCM applies a voltage to the temperature sensor through terminal THO1 of the TCM.
The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.
The TCM calculates the fluid temperature based on the voltage signal.
DTC No.
DTC Detection Condition
Trouble Area
P0711
  1. Both (a) and (b) are detected (2-trip detection logic):
    1. (a) Intake air and engine coolant temperature are more than -10°C (14°F) at engine start.
    2. (b) After normal driving for over 16 min. and 40 sec. or after driving 8 km (5 mile) or more, ATF temperature is less than 20°C (68°F).
  1. Transmission wire
  2. ATF temperature sensor
  3. TCM

MONITOR DESCRIPTION

This DTC indicates that there is a problem with output signals from the automatic transmission fluid (ATF) temperature sensor (TFT sensor) and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature and detects an open or short in the ATF temperature circuit or a fault of the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the TCM interprets this as a fault, and turns on the MIL.

WIRING DIAGRAM

C133262E02

INSPECTION PROCEDURE


DATA LIST

HINT:
According to the Data List displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the Data List as the first step in troubleshooting is one method to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn on the tester.

  6. Enter the following items: "Powertrain / ECT / Data List".

  7. According to the display on the tester, read "Data List".

    Tester Display
    Measurement Item/Range
    Normal Condition
    A/T Oil Temperature 1
    ATF Temperature Sensor Value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After Stall Test;
      Approx. 80°C (176°F)
    2. Equal to ambient temperature when cold soak

    HINT:
    1. When DTC P0712 is output and the intelligent tester indicates 150°C (302°F) or more, there is a short circuit.
    1. When DTC P0713 is output and the intelligent tester indicates -40°C (-40°F), there is an open circuit.
    1. Measure the resistance between terminal THO1 and body ground.

    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or more
    Short circuit

    HINT:
    1. If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.
    1. It is not necessary to inspect the circuit when P0711 is set.


1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0711)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester on.

  1. Select the following items: "Powertrain / ECT / DTC / Current or Pending".

  1. Read the DTCs using the intelligent tester.

    Result:
    Display (DTC output)
    Proceed to
    Only "P0711" is output
    A
    "P0711" and other DTCs are output
    B

    HINT:
    If any other codes besides "P0711" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2. CHECK TRANSMISSION FLUID LEVEL
  1. Check the transmission fluid level (Click here).

OK:
Automatic transmission fluid level is correct.



NG
ADD FLUID
OK


3. INSPECT TRANSMISSION WIRE

  1. C133212E01
    Remove the TCM from the transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    17 (E2) - 18 (THO1)
    90 Ω to 156 kΩ
    17 (E2) - Body ground
    10 kΩ or higher
    18 (THO1) - Body ground
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range with the ATF temperature shown in the table below, the driveability of the vehicle may decrease.

    Standard resistance:
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5.8 to 7.1 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ



OK
REPLACE TCM
NG


4. CHECK ATF TEMPERATURE SENSOR

  1. C133224E01
    Disconnect the ATF temperature sensor connector from the transmission wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    E2 - THO1
    90 Ω to 156 kΩ
    E2 - Body ground
    10 kΩ or higher
    THO1 - Body ground
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range with the ATF temperature shown in the table below, the driveability of the vehicle may decrease.

    Standard resistance:
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5.8 to 7.1 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ



NG
REPLACE ATF TEMPERATURE SENSOR ASSEMBLY
OK

REPLACE TRANSMISSION WIRE


← P0710 Transmission Fluid Temperature Sensor "A" Circuit (+ P0712, P0713) (from Oct 2006)P0715 Input / Turbine Speed Sensor Circuit Malfunction (+ P0717) (from Oct 2006) →