P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)
Diagnostic trouble codes · Vehicles built from Jun 2009
Also covers:
- P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)
- P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)
- P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2)
- P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)
- P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2)
Versions by build date: Oct 2006 – May 2009 from Jun 2009
CAUTION / NOTICE / HINT
DESCRIPTION
A three-way catalytic converter (TWC) is used in order to convert the carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NOx) into less harmful substances. To allow the TWC to function effectively, it is necessary to keep the air-fuel ratio of the engine near the stoichiometric air-fuel ratio. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, the Heated Oxygen (HO2) sensor is used.The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas becomes rich. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0136 P0156 |
|
|
| P0137 P0157 |
|
|
| P0138 P0158 |
|
|
WIRING DIAGRAM


CONFIRMATION DRIVING PATTERN
- HINT:
- This confirmation driving pattern is used in steps 5, 8 and 11 of the following diagnostic troubleshooting procedure when using an intelligent tester.
- Performing this confirmation driving pattern will activate the Heated Oxygen (HO2) sensor monitor. (The catalyst monitor is performed simultaneously.) This is very useful for verifying the completion of a repair.
- This confirmation driving pattern is used in steps 5, 8 and 11 of the following diagnostic troubleshooting procedure when using an intelligent tester.
- NOTICE:
- This test will not be completed if the vehicle is driven at an absolutely constant speed conditions such as with cruise control activated.


- Connect an intelligent tester to the DLC3.
- Turn the ignition switch on (IG).
- Turn the tester on.
- Clear the DTCs (where set) (Click here).
- Start the engine and warm it up (Procedure "A").
- Drive the vehicle at between 64 km/h and 113 km/h (40 mph and 70 mph) for at least 10 minutes (Procedure "B").
- On the tester, select the following menu items: Powertrain / Engine / DTC / Pending and check if any DTCs (any pending DTCs) are set.
INSPECTION PROCEDURE
- HINT:
- Malfunctioning areas can be identified by performing "Control the Injection Volume for A/F Sensor" provided in the Active Test . "Control the Injection Volume for A/F Sensor" can help to determine whether the Air-fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
- Connect the intelligent tester to the DLC3.
- Start the engine and turn the tester on.
- Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
- On the intelligent tester, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor.
- Perform "Control the Injection Volume for A/F Sensor" with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
- Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1 S1 and O2S B1 S2 or AFS Voltage B2 S1 and O2S B2 S2) displayed on the tester.
- HINT:
- "Control the Injection Volume for A/F Sensor" lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Each sensor reacts in accordance with increases in the fuel injection volume.
- "Control the Injection Volume for A/F Sensor" lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
| Tester Display (Sensor) |
Injection Volume |
Status |
Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (A/F) |
+25% |
Rich |
Less than 3.1 V |
| AFS Voltage B1S1 or AFS Voltage B2S1 (A/F) |
-12.5% |
Lean |
More than 3.4 V |
| O2S B1S2 or O2S B2S2 (HO2) |
+25% |
Rich |
More than 0.55 V |
| O2S B1S2 or O2S B2S2 (HO2) |
-12.5% |
Lean |
Less than 0.4 V |
- NOTICE:
- The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the HO2S (sensor 2) output has a maximum delay of 20 seconds.
| Case |
Air Fuel Ratio Sensor (Sensor 1) Output Voltage |
Heated Oxygen Sensor (Sensor 2) Output Voltage |
Main Suspected Trouble Area |
| 1 |
![]() ![]() |
![]() ![]() |
- |
| 2 |
![]() ![]() |
![]() ![]() |
|
| 3 |
![]() ![]() |
![]() ![]() |
|
| 4 |
![]() ![]() |
![]() ![]() |
|
- Performing "Control the Injection Volume for A/F Sensor" enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
- The following A/F Control procedure enables the technician to check and graph the voltage output of both the heated oxygen sensors. To display the graph, select the following menu items on the tester: View / Line Graph.
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
- If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be set.
- If the OX2B wire from the ECM connector is short-circuited to the +B wire, DTC P0156 will be set.
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
| 1. READ DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P0138 or P0158
A
P0137 or P0157
B
P0136 or P0156
C
|
|
||||
|
|
||||
| A | |
| 2. READ VALUE USING OXYGEN SENSOR (OUTPUT VOLTAGE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / O2S B1S2 or O2S B2S2.
Allow the engine to idle.
Read the Heated Oxygen (HO2) sensor output voltage while idling.
- Result:
HO2 Sensor Output Voltage
Proceed to
More than 1.2 V
A
Less than 1.0 V
B
|
|
||||
| A | |
| 3. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Turn the ignition switch off and wait for 5 minutes.

Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- RHD:
Tester Connection
Specified Condition
HT1B (C58-48) - OX1B (C58-88)
10 kΩ or higher
HT2B (C58-47) - OX2B (C58-87)
10 kΩ or higher
- LHD:
Tester Connection
Specified Condition
HT1B (C55-48) - OX1B (C55-88)
10 kΩ or higher
HT2B (C55-47) - OX2B (C55-87)
10 kΩ or higher
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 4. INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
Disconnect the C52 oxygen sensor connector (Bank 1 Sensor 2) or C51 oxygen sensor connector (Bank 2 sensor 2).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- Bank 1 sensor 2:
Tester Connection
Specified Condition
+B (2) - E2 (4)
10 kΩ or higher
+B (2) - OX1B (3)
10 kΩ or higher
- Bank 2 sensor 2:
Tester Connection
Specified Condition
+B (2) - E2 (4)
10 kΩ or higher
+B (2) - OX2B (3)
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 5. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0138 or P0158) |
On the intelligent tester, enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P0138 or P0158
A
No output
B
|
|
||||
| A | ||
| ||
| 7. READ VALUE USING OXYGEN SENSOR (OUTPUT VOLTAGE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Start the engine.
Enter the following menus: Powertrain / Engine / DTC / Data List / O2S B1S2 or O2S B1S2.
After warming up the engine, run the engine at an engine speed of 2,500 rpm for 3 minutes.
Read the output voltage of the HO2 sensor when the engine rpm is suddenly increased.
- HINT:
- Quickly accelerate the engine to 4,000 rpm 3 times using the accelerator pedal.
- Standard voltage:
- Fluctuates between 0.4 V or less and 0.55 V or more.
|
|
||||
| OK | |
| 8. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 9. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 or P0156) |
On the intelligent tester, enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P0136 or P0156
A
No output
B
|
|
||||
| A | |
| 10. REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 11. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 12. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 or P0156) |
On the intelligent tester, enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P0136 or P0156
A
No output
B
|
|
||||
| A | |
| 13. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.
Change the fuel injection volume using the tester, while monitoring the output voltage of Air-Fuel Ratio (A/F) and HO2 sensor displayed on the tester.
- HINT:
- Change the fuel injection volume within the range of -12% and +12%. The injection volume can be changed in 1% graduations within the range.
- The A/F sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the HO2 sensor is displayed as O2S B1S2 or O2S B2S2, on the intelligent tester.
- Change the fuel injection volume within the range of -12% and +12%. The injection volume can be changed in 1% graduations within the range.
- Result:
Tester Display (Sensor)
Voltage Variation
Proceed to
AFS Voltage B1S1 (A/F)
AFS Voltage B2S1 (A/F)
Alternates between more and less than 3.3 V
OK
AFS Voltage B1S1 (A/F)
AFS Voltage B2S1 (A/F)
Remains more than 3.3 V
NG
AFS Voltage B1S1 (A/F)
AFS Voltage B2S1 (A/F)
Remains less than 3.3 V
NG
- HINT:
- A normal HO2 sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the A/F sensor voltage remains either less or more than 3.3 V despite the HO2 sensor indicating a normal reaction, the A/F sensor is malfunctioning.


|
|
||||
| OK | ||
| ||
| 14. INSPECT FOR EXHAUST GAS LEAK |
- OK:
- No gas leakage.
|
|
||||
| OK | |
| 15. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Disconnect the C52 oxygen sensor connector (Bank 1 Sensor 2) or C51 oxygen sensor connector (Bank 2 sensor 2).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- Bank 1 sensor 2:
Tester Connection
Condition
Specified Condition
HT1B (1) - +B (2)
20°C (68°F)
11 to 16 Ω
HT1B (1) - E2 (4)
Always
10 kΩ or higher
- Bank 2 sensor 2:
Tester Connection
Condition
Specified Condition
HT2B (1) - +B (2)
20°C (68°F)
11 to 16 Ω
HT2B (1) - E2 (4)
Always
10 kΩ or higher
|
|
||||
| OK | |
| 16. INSPECT ENGINE ROOM JUNCTION BLOCK (EFI RELAY) |
Remove the engine room junction block from the engine room R/B.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminal Connection
Specified Condition
1E-12 - 1E-6
10 kΩ or higher
1E-12 - 1E-6
Below 1 Ω
(when battery voltage applied to terminals 1E-9 and 1E-10)
Reinstall the engine room junction block.
|
|
||||
| OK | |
| 17. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the C52 oxygen sensor connector (Bank 1 Sensor 2) or C51 oxygen sensor connector (Bank 2 sensor 2).

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Terminal Connection
Specified Condition
+B (C52-2) - Body ground
9 to 14 V
+B (C51-2) - Body ground
9 to 14 V
Turn the ignition switch off.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
- RHD:
Terminal Connection
Specified Condition
HT1B (C52-1) - HT1B (C58-48)
Below 1 Ω
OX1B (C52-3) - OX1B (C58-88)
Below 1 Ω
E2 (C52-4) - EX1B (C58-65)
Below 1 Ω
HT2B (C51-1) - HT2B (C58-47)
Below 1 Ω
OX2B (C51-3) - OX2B (C58-87)
Below 1 Ω
E2 (C51-4) - EX2B (C58-64)
Below 1 Ω
- LHD:
Terminal Connection
Specified Condition
HT1B (C52-1) - HT1B (C55-48)
Below 1 Ω
OX1B (C52-3) - OX1B (C55-88)
Below 1 Ω
E2 (C52-4) - EX1B (C55-65)
Below 1 Ω
HT2B (C51-1) - HT2B (C55-47)
Below 1 Ω
OX2B (C51-3) - OX2B (C55-87)
Below 1 Ω
E2 (C51-4) - EX2B (C55-64)
Below 1 Ω
- Standard resistance (Check for short):
- RHD:
Terminal Connection
Specified Condition
HT1B (C52-1) or HT1B (C58-48) - Body ground
10 kΩ or higher
OX1B (C52-3) or OX1B (C58-88) - Body ground
10 kΩ or higher
E2 (C52-4) or EX1B (C58-65) - Body ground
10 kΩ or higher
HT2B (C51-1) or HT2B (C58-47) - Body ground
10 kΩ or higher
OX2B (C51-3) or OX2B (C58-87) - Body ground
10 kΩ or higher
E2 (C51-4) or EX2B (C58-64) - Body ground
10 kΩ or higher
- LHD:
Terminal Connection
Specified Condition
HT1B (C52-1) or HT1B (C55-48) - Body ground
10 kΩ or higher
OX1B (C52-3) or OX1B (C55-88) - Body ground
10 kΩ or higher
E2 (C52-4) or EX1B (C55-65) - Body ground
10 kΩ or higher
HT2B (C51-1) or HT2B (C55-47) - Body ground
10 kΩ or higher
OX2B (C51-3) or OX2B (C55-87) - Body ground
10 kΩ or higher
E2 (C51-4) or EX2B (C55-64) - Body ground
10 kΩ or higher
Reconnect the HO2 sensor connector.
Reconnect the ECM connector.


|
|
||||
| OK | ||
| ||




