HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshooting · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
- NOTICE:
- DTCs for the CAN communication system are as follows: U0073, U0100, U0101, U0123, U0124, U0126, U0129, U0182, U1002, B1207, B1297, B1499, and B2326.
- Refer to troubleshooting of each system if DTCs regarding the CAN communication system are not output.
- DTCs for the CAN communication system are as follows: U0073, U0100, U0101, U0123, U0124, U0126, U0129, U0182, U1002, B1207, B1297, B1499, and B2326.
| 1.CHECK BATTERY |
- Standard Voltage:
- 11 to 14 V
- HINT:
- If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
| |||||
| 2.CHECK AND CLEAR DTCS |
- HINT:
- CAN communication DTCs are stored when there is an open or short in any of the communication wires. Any problems with the power source of a corresponding ECU or sensor, or problems in the ECU or the sensor itself also cause these DTCs to be stored.
- If a CAN communication wire connector is disconnected with the power switch on (IG), the ECUs of the corresponding system and related systems store a DTC.
- CAN communication DTCs are stored when there is an open or short in any of the communication wires. Any problems with the power source of a corresponding ECU or sensor, or problems in the ECU or the sensor itself also cause these DTCs to be stored.
| |||||
| 3.CHECK CAN NO. 1 BUS WIRE |
Check the CAN No. 1 bus wire (Click here).
- HINT:
- If the area where an open or short is occurring in a CAN No. 1 bus wire can be determined, refer to the Problem Symptoms Table (Click here).
| |||||
| 4.CHECK WITH INTELLIGENT TESTER |
Using the intelligent tester, display the "Communication Bus Check" screen (Click here).
Observe the screen for approximately 1 minute to check the ECUs and sensors displayed on the screen.
- Result:
Symptom
Proceed to
All ECUs and sensors connected to the CAN communication system are displayed on the screen.
(CAN bus circuit is currently normal.)
A
One of the ECUs and sensors connected to the CAN No. 1 bus is not displayed on the screen.
(Open in ECU or sensor branch wires, or communication interrupted.)
B
All ECUs connected to the CAN No. 2 bus and gateway ECU are not displayed on the screen.
(Open in network gateway ECU branch wire or gateway ECU malfunction.)
C
- All ECUs and sensors except the gateway ECU connected to the CAN No. 2 bus are not displayed on the screen.
- The gateway ECU outputs DTC U1002.
D
All ECUs connected to the CAN MS bus and main body ECU are not displayed on the screen.
(Open in main body ECU branch wire or main body ECU malfunction.)
E
- All ECUs and sensors except the main body ECU connected to the CAN MS bus are not displayed on the screen.
- The main body ECU outputs DTC B2326.
F
One of the ECUs and sensors connected to the CAN No. 2 bus or CAN MS bus is not displayed on the screen.
G
Some ECUs and sensors repeatedly appear and disappear on the screen during this check.
(Open in one side of ECU or sensor branch wires)
H
- All ECUs and sensors except the gateway ECU connected to the CAN No. 2 bus are not displayed on the screen.
- NOTICE:
- The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.
- Non-installed ECUs or sensors will not be displayed. Do not mistake them for being in communication stop mode.
- The ECUs and sensors that repeatedly appear and disappear from the screen during this check are considered normal. (The response to the intelligent tester and its display are affected by signals output from other ECUs which have an open circuit in either of their CAN bus branch wires.)
- The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.
- HINT:
- The ECUs and sensors connected to the CAN No. 2 bus are displayed on the screen by the gateway ECU.
- The ECUs and sensors connected to the CAN MS bus are displayed on the screen by the main body ECU.
- The ECUs and sensors connected to the CAN No. 2 bus are displayed on the screen by the gateway ECU.
|
|||||
|
|||||
|
|||||
|
|||||
|
|||||
|
|||||
|
|||||
| |||||
| 5.RECHECK DTC |
- HINT:
- Sometimes CAN communication system DTCs are output, but all ECUs and sensors connected to the CAN communication system are displayed on the intelligent tester. In this case, previous or history DTCs may indicate the cause of the problem.
- ECUs related to a problem in the CAN bus will store DTCs to indicate communication malfunctions. Communication stop mode in the CAN bus can be determined by comparing the combination of DTCs that have been set. Refer to DTC Combination Table for the CAN bus.
- The gateway ECU will store communication error DTCs when the ECUs connected to the CAN No. 2 bus cannot communicate, or if a network malfunction occurs.
- The main body ECU will store communication error DTCs when the ECUs connected to the CAN MS bus cannot communicate, or if a network malfunction occurs.
- Sometimes CAN communication system DTCs are output, but all ECUs and sensors connected to the CAN communication system are displayed on the intelligent tester. In this case, previous or history DTCs may indicate the cause of the problem.
- Result:
Result
Proceed to
Communication error DTCs other than the codes output from the gateway ECU and/or main body ECU ECU is output.
A
The gateway ECU outputs DTC 1002.
(A malfunction occurred in the CAN No. 2 bus.)
B
The main body ECU outputs DTC B2326.
(A malfunction occurred in the CAN MS bus.)
C
The gateway ECU or main body ECU output DTCs other than DTC U1002 or B2326.
D
|
|||||
|
|||||
|
|||||
| |||||
| 6.DTC COMBINATION TABLE |
Confirm trouble according to the combination of output DTCs regarding the CAN communication system (Click here).
- HINT:
- Previous CAN communication system DTCs may be the cause if CAN communication system DTCs are output and all ECUs and sensors connected to the CAN communication system are displayed on "Communication Bus Check" of the intelligent tester.
| |||||
| 7.CIRCUIT INSPECTION |
| |||||
| 8.IDENTIFICATION OF PROBLEM |
| |||||
| 9.REPAIR OR REPLACE |
| |||||
| 10.CONFIRMATION TEST |
| |||||