2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM
  1. CAN No. 1 Bus

    1. ECM

    2. Skid control ECU

    3. Steering angle sensor

    4. Yaw rate sensor

    5. Center airbag sensor

    6. Main body ECU

    7. Air conditioning amplifier

    8. Combination meter

    9. Network gateway ECU

  2. CAN No. 2 Bus

    1. AFS ECU

  3. CAN MS Bus

    1. Certification ECU

    2. Clearance warning ECU


BUS CHECK (COMMUNICATION MALFUNCTION DTC)

HINT:
Only CAN communication system DTCs for each ECU can be displayed on the intelligent tester.

  1. G029877E01
    Select "Bus Check" from the "System Select" screen on the intelligent tester.

  2. G029878
    Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".

  3. G029879
    Select the system of the DTC to be checked and select "Details".

  4. G029880
    CAN communication system DTC(s) is/are displayed.


BUS CHECK (COMMUNICATION BUS CHECK)

HINT:
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.

  1. G029877E01
    Select "Bus Check" from the "System Select" screen on the intelligent tester.

  2. G029878
    Select "Communication Bus Check" from the "Bus Check" screen.

  3. C128178
    The screen displays the ECUs and sensors that are properly connected to the CAN communication system.

    HINT:
    If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system.

  4. C128179
    "There is no system connected to the communication bus" is displayed if there are no ECUs or sensors connected to the CAN bus.


CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION
  1. Systems (ECUs, sensors) that adopt CAN communication vary depending on the vehicle's optional settings. Check which systems (ECUs, sensors) are installed on the vehicle.

    ECU/Sensor name
    Check method
    Skid control ECU
    Installed on all vehicles
    Steering angle sensor
    Installed on all vehicles
    Yaw rate sensor
    Installed on all vehicles
    ECM
    Installed on all vehicles
    Center airbag sensor
    Installed on all vehicles
    Air conditioning amplifier
    Installed on all vehicles
    Combination meter
    Installed on all vehicles
    Main body ECU
    Installed on all vehicles
    Certification ECU
    Installed on all vehicles
    Clearance warning ECU
    Installed on all vehicles
    Gateway ECU
    Installed on all vehicles
    AFS ECU
    Installed on all vehicles


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, CAN communication system DTCs can be displayed by the ECU using the intelligent tester.
  2. If CAN communication system DTCs are output, trouble cannot be determined only by the DTCs. Perform troubleshooting according to "HOW TO PROCEED WITH TROUBLESHOOTING". (Click here)

  1. ECM

    DTC No.
    Detection Item
    U0101*1
    High speed CAN Communication Bus

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *1: The ECM is malfunctioning if only U0101 is output. Refer to SFI system (Click here).

  2. ECT

    DTC No.
    Detection Item
    U0100*2
    High speed CAN Communication Bus

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *2: The ECM is malfunctioning if only U0100 is output. Refer to Automatic Transaxle system (Click here).

  3. SKID CONTROL ECU

    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus Off
    U0100
    Lost Communication with ECM/PCM "A"
    U0123
    Lost Communication with Yaw Rate Sensor Module
    U0124
    Lost Communication with Lateral Acceleration Sensor Module
    U0126
    Lost Communication with Steering Angle Sensor Module

    HINT:
    DTC communication uses the CAN communication system.

  4. COMBINATION METER

    DTC No.
    Detection Item
    U0100
    Lost Communication with ECM/PCM "A"
    U0129
    Lost Communication with Brake System Control Module

    HINT:
    DTC communication uses the CAN communication system.

  5. AIR CONDITIONER AMPLIFIER

    DTC No.
    Detection Item
    B1499
    Multiplex Communication Circuit

    HINT:
    DTC communication is via the CAN communication system.

  6. MAIN BODY ECU

    DTC No.
    Detection Item
    B1207*3
    Certification ECU Communication Malfunction
    B2326*3
    CAN MS Bus Line Communication Malfunction

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *3: The main body ECU is malfunctioning if B1207 and/or B2326 are output alone. Refer to DTC chart (Click here).

  7. GATEWAY ECU

    DTC No.
    Detection Item
    U0182*4
    Lost Communication with AFS ECU
    U1002*4
    Lost Communication with Gateway Module

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *4: The gateway ECU is malfunctioning if U0182 and/or U1002 are output alone. Refer to DTC chart (Click here).

  8. AFS ECU

    DTC No.
    Detection Item
    B2427
    CAN Communication Malfunction

    HINT:
    DTC communication is via the CAN communication system.

  9. CENTER AIRBAG SENSOR

    HINT:
    The center airbag sensor is connected to the CAN communication system, but CAN communication DTCs are not output.

  10. STEERING ANGLE SENSOR

    HINT:
    The steering angle sensor is connected to the CAN communication system, but CAN communication DTCs are not output.

  11. YAW RATE SENSOR

    HINT:
    The yaw rate sensor is connected to the CAN communication system, but CAN communication DTCs are not output.

  12. CERTIFICATION ECU

    HINT:
    The certification ECU is connected to the CAN communication system, but CAN communication DTCs are not output.

  13. CLEARANCE WARNING ECU

    HINT:
    The clearance warning ECU is connected to the CAN communication system, but CAN communication DTCs are not output.


DTC COMBINATION TABLE
  1. CAN No. 1 Bus

    DTC
    Trouble Mode
    Output from
    Output DTC
    ECM Communication Stop Mode
    Skid Control ECU Communication Stop Mode
    Steering Angle Sensor Communication Stop Mode
    Yaw Rate Sensor Communication Stop Mode
    Combination Meter ECU Communication Stop Mode
    Skid Control ECU
    U0073
    X
    X
    X
    X
    X
    U0100
    □ During driving
    X
    X
    X
    X
    U0123
    X
    X
    X
    ○
    X
    U0124
    X
    X
    X
    ○
    X
    U0126
    X
    X
    X
    X
    X
    Combination Meter ECU
    U0100
    ○
    X
    X
    X
    X
    U0129
    X
    ○
    X
    X
    X

    HINT:
    1. ○: Set
    2. X: Not set or may be set according to the malfunctioning part when one side of the CAN bus wire opens
    3. □: Set under the condition shown in the table above

    DTC
    Trouble Mode
    Output from
    Output DTC
    Air Conditioning Amplifier Communication Stop Mode
    Center Airbag Sensor Communication Stop Mode
    Gateway ECU Communication Stop Mode
    Main Body ECU Communication Stop Mode
    Skid Control ECU
    U0073
    X
    X
    X
    X
    U0100
    X
    X
    X
    X
    U0123
    X
    X
    X
    X
    U0124
    X
    X
    X
    X
    U0126
    X
    X
    X
    X
    Combination Meter ECU
    U0100
    X
    X
    X
    X
    U0129
    X
    X
    X
    X

    HINT:
    1. ○: Set
    2. X: Not set or may be set according to the malfunctioning part when one side of the CAN bus wire opens
    3. Skid Control ECU Communication Stop Mode (Click here)
    4. Steering Angle Sensor Communication Stop Mode (Click here)
    5. Yaw Rate Sensor Communication Stop Mode (Click here)
    6. ECM Communication Stop Mode (Click here)
    7. Main Body ECU Communication Stop Mode (Click here)
    8. Center Airbag Sensor Communication Stop Mode (Click here)
    9. Gateway ECU Communication Stop Mode (Click here)

← DIAGNOSIS SYSTEM (Oct 2006 – May 2009)FAIL-SAFE CHART (from Oct 2006) →