2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

Short to GND in CAN Bus Line

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

A short to GND is suspected in the CAN bus wire when the resistance between terminals 4 (CG) and 6 (CANH), or terminals 4 (CG) and 14 (CANL) of the DLC3 is below 200 Ω.
Symptoms
Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG), or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
  1. Short to GND in CAN bus wire
  2. ECM
  3. Skid control ECU
  4. Steering angle sensor
  5. Yaw rate sensor
  6. Main body ECU
  7. Air Conditioning amplifier
  8. Center airbag sensor assembly
  9. Combination meter
  10. Gateway ECU

WIRING DIAGRAM

C212182E02
C212183E03

INSPECTION PROCEDURE

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the engine switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (DLC3 BRANCH WIRE)

  1. C133233E03
    Turn the engine switch off.

  1. Disconnect DLC3 branch wire connector E62 from the CAN No. 1 J/C "B" side (without earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. C126231E13
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher

  1. Reconnect DLC3 branch wire connector E62 to the CAN No. 1 J/C "B" side (without earth terminal).



NG
REPAIR OR REPLACE DLC3 BRANCH WIRE OR CONNECTOR
OK


2. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (CAN NO. 1 J/C WIRE)

  1. C142743E03
    Disconnect CAN main bus wire connector E42 from the CAN No. 1 J/C "A" side (with earth terminal).

  1. C126231E13
    Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



OK
Go to step 6
NG


3. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (CAN NO. 1 J/C WIRE)

  1. C126231E13
    Disconnect connectors from the CAN No. 1 J/C one at a time.

    HINT:
    Disconnect the ECU and sensor connectors other than the DLC3 branch wires and CAN main bus wires between the CAN No. 1 J/C and CAN No. 4 J/C.

  1. Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.C212178E01
    C152831E01

    CAN No. 1 J/C Connector ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Center Airbag Sensor Assembly (E45)
    Black
    B
    W
    CAN No. 1 J/C Connector ("B" side, without earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Yaw Rate Sensor (E46)
    Blue
    B
    W
    Steering Angle Sensor (E63)
    Brown
    B
    W
    Combination Meter (E43)
    White
    B
    W
    Main Body ECU (E44)
    Black
    B
    W

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to GND in 2 or more CAN bus wires.

  1. When there is a short to GND in one or more of the bus wires that connect to an ECU (or sensor):

    1. Reconnect all of the connectors to the CAN No. 1 J/C, except for the one that was disconnected last (the bus wire that is shorted to GND). Check that the resistance shown on the tester is normal (200 Ω or more) to confirm that there is a short to GND in one branch wire only.

      HINT:
      1. The connectors connected to the CAN No. 1 J/C can be distinguished according to the color of the communication bus wires and the shape of the connectors.
      2. Reconnecting the connectors to non-specified positions on the CAN No. 1 J/C does not affect system operation. However, it is preferred to reconnect the connectors to their specified positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


NEXT


4. RECONNECT CONNECTOR
  1. Reconnect the connector of the bus wire that is shorted to GND to the CAN No. 1 J/C (the connector that caused the bus wire resistance to change to 200 Ω or more when it was disconnected).


NEXT


5. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE

  1. C126231E13
    Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the bus wire shorted to GND is connected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher

    HINT:
    If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR

6. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (CAN NO. 4 J/C WIRE)
  1. Reconnect CAN main bus wire connector E42 to the CAN No. 1 J/C "A" side (with earth terminal).

  1. C133245E17
    Disconnect CAN No. 4 J/C connector A40.

  1. C126231E13
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



OK
Go to step 11
NG


7. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (CAN NO. 1 J/C - CAN NO. 4 J/C)
  1. Reconnect CAN No. 4 J/C connector A40.

  1. C133246E13
    Disconnect CAN No. 4 J/C connector E41.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E41-4 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E41-10 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN NO. 1 BUS MAIN WIRE OR CONNECTOR (CAN NO. 1 J/C - CAN NO. 4 J/C)
OK


8. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (GATEWAY ECU BRANCH WIRE)

  1. C133246E19
    C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E41-3 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E41-9 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
Go to step 10
OK


9. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (A/C AMPLIFIER BRANCH WIRE)

  1. C133245E20
    Disconnect A/C amplifier connector E38.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E41-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E41-7 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher

    HINT:
    Measure the resistance with CAN No. 4 J/C connector E41 disconnected.



NG
REPAIR OR REPLACE CAN NO. 1 BUS BRANCH WIRE OR CONNECTOR (A/C AMPLIFIER BRANCH WIRE)
OK

REPLACE A/C AMPLIFIER

10. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (GATEWAY ECU BRANCH WIRE)

  1. C133246E57
    Disconnect gateway ECU connector E70.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E41-2 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E41-8 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher

    HINT:
    Measure the resistance with CAN No. 4 J/C connector E41 disconnected.



NG
REPAIR OR REPLACE CAN NO. 1 BUS BRANCH WIRE OR CONNECTOR (GATEWAY ECU BRANCH WIRE)
OK

REPLACE GATEWAY ECU

11. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (ECM MAIN BUS WIRE)

  1. C133245E14
    Disconnect CAN No. 4 J/C connector A40.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A40-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    A40-7 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



OK
Go to step 13
NG


12. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (ECM)

  1. C133245E14
    Disconnect ECM connector A55.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A40-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    A40-7 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher

    HINT:
    Measure the resistance with CAN No. 4 J/C connector A40 disconnected.



NG
REPAIR OR REPLACE CAN NO. 1 BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU BRANCH WIRE)
OK

REPLACE ECM

13. CHECK FOR SHORT TO GND IN CAN NO. 1 BUS WIRE (SKID CONTROL ECU)

  1. C133245E19
    Disconnect skid control ECU connector A26.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A40-2 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    A40-8 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



OK
REPLACE BRAKE ACTUATOR ASSEMBLY
NG

REPAIR OR REPLACE CAN NO. 1 BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU BRANCH WIRE)


← Short to GND in CAN Bus Line (Oct 2006 – May 2009)Open in One Side of CAN Branch Line (Oct 2006 – May 2009) →