TERMINALS OF ECU
System information · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
- NOTICE:
- Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- HINT:
- Operating the engine switch, any other switches, or a door triggers related ECU and sensor communication on the CAN.
- This communication will cause the resistance value to change.
- NOTICE:
- This section describes the standard CAN values for all CAN related components.
| JUNCTION CONNECTOR FOR CAN NO. 1 BUS |
CAN No. 1 J/C


CAN No. 1 J/C Connector ("A" side, with earth terminal)
Connector Color
Color (CAN-H Side)
Color (CAN-L Side)
CAN No. 1 Bus Main Wire (E42)
White
B
W
Center Airbag Sensor Assembly (E45)
Black
B
W
CAN No. 1 J/C Connector ("B" side, without earth terminal)
Connector Color
Color (CAN-H Side)
Color (CAN-L Side)
Yaw Rate Sensor (E46)
Blue
B
W
DLC3 (E62)
White
B
W
Steering Angle Sensor (E63)
Brown
B
W
Combination Meter (E43)
White
B
W
Main Body ECU (E44)
Black
B
W
CAN No. 4 J/C (REAR OF THE VEHICLE)


Wiring color: Terminal
Wiring Color
Destination
A40-1 (CANH)
B
ECM (CANH)
A40-7 (CANL)
W
ECM (CANL)
A40-2 (CANH)
B
Skid Control ECU (CANH)
A40-8 (CANL)
W
Skid Control ECU (CANL)
CAN No. 4 J/C (FRONT OF THE VEHICLE)


Wiring color: Terminal
Wiring Color
Destination
E41-1 (CANH)
B
A/C Amplifier (CANH)
E41-7 (CANL)
W
A/C Amplifier (CANL)
E41-2 (CANH)
B
Gateway ECU(CANH)
E41-8 (CANL)
W
Gateway ECU(CANL)
E41-4 (CANH)
B
CAN No. 1 J/C (CANH)
E41-10 (CANL)
W
CAN No. 1 J/C (CANL)
The connection diagram of the components which are connected to the CAN J/C


| JUNCTION CONNECTOR FOR CAN NO. 2 BUS |
CAN No. 2 J/C


Wiring color: CAN No. 3 J/C Connector ("A" side, with earth terminal)
Connector Color
Color (CAN-H Side)
Color (CAN-L Side)
CAN No. 2 Bus Main Wire (E79)
White
R
W
AFS ECU (E80)
Black
R
W
| JUNCTION CONNECTOR FOR CAN MS BUS |
CAN No. 3 J/C


Wiring color: CAN No. 3 J/C Connector ("A" side, with earth terminal)
Connector Color
Color (CAN-H Side)
Color (CAN-L Side)
Certification ECU (O34)
Gray
L
W
Clearance Warning ECU (O32)
Blue
L
W
CAN MS Bus Main Wire (O33)
White
L
W
| DLC3 |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E10-6 (CANH) - E10-14 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E10-6 (CANH) - E10-4 (CG)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E10-14 (CANL) - E10-4 (CG)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E10-6 (CANH) - E10-16 (BAT)
B - L
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E10-14 (CANL) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| ECM |
Disconnect the connector from the ECM.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Condition
Specified Value
A55-41 (CANH) - A55-49 (CANL)
Engine switch off
108 to 132 Ω
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
A55-41 (CANH) - A55-49 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
A55-41 (CANH) - C55-81 (E1)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A55-49 (CANL) - C55-81 (E1)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A55-41 (CANH) - A55-20 (BATT)
B - Y
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
A55-49 (CANL) - A55-20 (BATT)
W - Y
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| SKID CONTROL ECU WITH ACTUATOR |
Disconnect the connector from the skid control ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
A26-35 (CANH) - A26-14 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
A26-35 (CANH) - A26-4 (GND1)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A26-14 (CANL) - A26-4 (GND1)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A26-35 (CANH) - A26-3 (+BS)
B - L
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
A26-14 (CANL) - A26-3 (+BS)
W - L
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| STEERING ANGLE SENSOR |
Disconnect the connector from the steering angle sensor.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E17-10 (CANH) - E17-9 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E17-10 (CANH) - E17-2 (ESS)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E17-9 (CANL) - E17-2 (ESS)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E17-10 (CANH) - E17-3 (BAT)
B - W
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E17-9 (CANL) - E17-3 (BAT)
W - W
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| YAW RATE SENSOR |
Disconnect the connector from the yaw rate sensor.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E34-2 (CANH) - E34-3 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E34-2 (CANH) - E34-4 (GND)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E34-3 (CANL) - E34-4 (GND)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E34-2 (CANH) - E10-16 (BAT)
B - L
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E34-3 (CANL) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| CENTER AIRBAG SENSOR |
Disconnect the connector from the center airbag sensor.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E30-13 (CANH) - E30-22 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E30-13 (CANH) - E30-25 (E1)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E30-22 (CANL) - E30-25 (E1)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E30-13 (CANH) - E10-16 (BAT)
B - L
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E30-22 (CANL) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| AIR CONDITIONING AMPLIFIER |
Disconnect the connector from the air conditioning amplifier.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E38-11 (CANH) - E38-12 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E38-11 (CANH) - E38-14 (GND)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E38-12 (CANL) - E38-14 (GND)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E38-11 (CANH) - E38-21 (B)
B - GR
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E38-12 (CANL) - E38-21 (B)
W - GR
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| COMBINATION METER |
Disconnect the connector from the combination meter.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Condition
Specified Value
F1-17 (CANH) - F1-18 (CANL)
Engine switch off
108 to 132 Ω
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
F1-17 (CANH) - F1-18 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
F1-17 (CANH) - F1-12 (E2)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
F1-18 (CANL) - F1-12 (E2)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
F1-17 (CANH) - F1-2 (B2)
B - R
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
F1-18 (CANL) - F1-2 (B2)
W - R
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| MAIN BODY ECU (INSTRUMENT PANEL J/B) |
Disconnect the connector from the main body ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Condition
Specified Value
E8-16 (CANP) - E8-15 (CANN)
Engine switch off
108 to 132 Ω
Measure the resistance according to the value(s) in the table below.


- Standard resistance:
CAN No. 1 Bus Branch Wire Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E8-5 (CANH) - E8-6 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E8-5 (CANH) - E10-4 (CG)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-6 (CANL) - E10-4 (CG)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-5 (CANH) - E10-16 (BAT)
B - L
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E8-6 (CANL) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
- Standard resistance:
CAN MS Bus Main Wire Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E8-16 (CANP) - E8-15 (CANN)
L - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
E8-16 (CANP) - E10-4 (CG)
L - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-15 (CANN) - E10-4 (CG)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-16 (CANP) - E10-16 (BAT)
L - L
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E8-15 (CANN) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| CERTIFICATION ECU |
Disconnect the connector from the certification ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Condition
Specified Value
E58-27 (CANH) - E58-28 (CANL)
Engine switch off
108 to 132 Ω
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E58-27 (CANH) - E58-28 (CANL)
L - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
E58-27 (CANH) - E58-17 (E)
L - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E58-28 (CANL) - E58-17 (E)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E58-27 (CANH) - E58-1 (+B)
L - W
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E58-28 (CANL) - E58-1 (+B)
W - W
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| CLEARANCE WARNING ECU |
Disconnect the connector from the clearance warning ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
O30-3 (R1) - O30-5 (R2)
L - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
O30-3 (R1) - O30-17 (E)
L - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
O30-5 (R2) - O30-17 (E)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
O30-3 (R1) - E10-16 (BAT)
L - L
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
O30-5 (R2) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| GATEWAY ECU |
Disconnect the connector from gateway ECU.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Condition
Specified Value
E70-13 (CA2H) - E70-12 (CA2L)
Engine switch off
108 to 132 Ω
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
CAN No. 1 Bus Branch Wire Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E70-16 (CA1H) - E70-15 (CA1L)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E70-16 (CA1H) - E70-4 (GND)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E70-15 (CA1L) - E70-4 (GND)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E70-16 (CA1H) - E70-2 (BATT)
B - W
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E70-15 (CA1L) - E70-2 (BATT)
W - W
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
- Standard resistance:
CAN No. 2 Bus Main Wire Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E70-13 (CA2H) - E70-12 (CA2L)
R - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E70-13 (CA2H) - E70-4 (GND)
R - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E70-12 (CA2L) - E70-4 (GND)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E70-13 (CA2H) - E70-2 (BATT)
R - W
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E70-12 (CA2L) - E70-2 (BATT)
W - W
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
| AFS ECU |
Disconnect the connector from the AFS ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
A61-12 (MPX1) - A61-13 (MPX2)
R - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
A61-12 (MPX1) - A61-22 (EIS)
R - W
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A61-13 (MPX2) - A61-22 (EIS)
W - W
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
A61-12 (MPX1) - E10-16 (BAT)
R - L
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
A61-13 (MPX2) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher