2006-2011 Camry Aurion · Service Manual BODY

Rear Sunshade does not Operate with Rear Sunshade Switch

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

SYSTEM DESCRIPTION

When the rear sunshade switch is pressed, a signal is sent directly to the rear sunshade relay.

WIRING DIAGRAM

B149985E03

INSPECTION PROCEDURE


1. INSPECT FUSE (GAUGE NO. 1)
  1. Remove the GAUGE No. 1 fuse from the instrument panel J/B.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2. INSPECT REAR SUNSHADE SWITCH ASSEMBLY

  1. E141000E01
    Disconnect the E74 connector.

  1. Measure the resistance between the terminals according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    E74-1 - E74-4 (*1)
    E74- 3 - E74-4 (*2)
    Rear sunshade switch is pressed
    Below 1 Ω
    E74-1 - E74-4 (*1)
    E74-3 - E74-4 (*2)
    Rear sunshade switch is not pressed
    10 kΩ or higher

    *1: except RHD with the 2GR-FE*2: RHD with the 2GR-FE



NG
REPLACE REAR SUNSHADE SWITCH
OK


3. CHECK WIRE HARNESS AND CONNECTOR (REAR SUNSHADE SWITCH - REAR SUNSHADE RELAY AND BODY GROUND)

  1. E141001E01
    Disconnect the E74 and N41 connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester connection
    Specified condition
    E74-4 - SW (N41-5)
    Below 1 Ω
    E74-1 - Body ground (*1)
    E74-3 - Body ground (*2)
    Below 1 Ω
    E (N41-7) - Body ground
    Below 1 Ω
    SW (N41-5) - Body ground
    10 kΩ or higher

    *1: except RHD with the 2GR-FE*2: RHD with the 2GR-FE



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT REAR SUNSHADE MOTOR
B131209E01
  1. Disconnect the N42 connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester connection
    Specified condition
    N42-1 - N42-2
    Below 1 Ω
    N42-1 - Body ground
    10 kΩ or higher



NG
REPLACE REAR SUNSHADE MOTOR
OK


5. CHECK WIRE HARNESS AND CONNECTOR (REAR SUNSHADE MOTOR - REAR SUNSHADE RELAY)

  1. B131210E01
    Disconnect the N42 and N41 connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester connection
    Specified condition
    N42-1 - MOP (N41-9)
    Below 1 Ω
    N42-2 - MCL (N41-10)
    Below 1 Ω
    MOP (N41-9) - Body ground
    10 kΩ or higher
    MCL (N41-10) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR SUNSHADE RELAY


← Rear Sunshade does not Operate with Rear Sunshade Switch (Oct 2006 – May 2009)Rear Sunshade Shift-linked Function does not Operate when Shift Lever is Moved to R Position (Jun 2006 – Sep 2006) →