2006-2011 Camry Aurion · Service Manual SUSPENSION & AXLE

INSPECTION

Inspection · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:
    for Australia: 
    Tire size
    Front kPa (kgf*cm2, psi)
    Rear kPa (kgf*cm2, psi)
    215/60R16 95V
    4 passengers or less
    210 (2.1, 31)*1, 230 (2.3, 33)*2
    210 (2.1, 31)*1, 230 (2.3, 33)*2
    5 passengers
    240 (2.4, 35)*1, 300 (3.1, 44)*2
    240 (2.4, 35)*1, 300 (3.1, 44)*2
    215/55R17 93V
    4 passengers or less
    220 (2.2, 32)*1, 250 (2.5, 36)*2
    220 (2.2, 32)*1, 250 (2.5, 36)*2
    5 passengers
    240 (2.4, 35)*1, 300 (3.1, 44)*2
    240 (2.4, 35)*1, 300 (3.1, 44)*2

    *1: For driving at under 140 km/h (87 mph).
    *2: For driving at over 140 km/h (87 mph).

    Cold tire inflation pressure:
    for GCC: 
    Tire size
    Front kPa (kgf*cm2, psi)
    Rear kPa (kgf*cm2, psi)
    215/60R16 95V
    210 (2.1, 31)*1, 240 (2.4, 35)*2
    210 (2.1, 31)*1, 240 (2.4, 35)*2
    215/55R17 93V
    220 (2.2, 32)*1, 240 (2.4, 35)*2
    220 (2.2, 32)*1, 240 (2.4, 35)*2

    *1: For driving at under 160 km/h (100 mph).
    *2: For driving at over 160 km/h (100 mph).

  1. C137874
    Using a dial indicator, check the runout of the tires.

    Tire runout:
    1.4 mm (0.055 in.) or less


ROTATE TIRES

  1. R014931E05
    Rotate the tires as shown in the illustration.


INSPECT WHEEL BALANCE

  1. Check and adjust the off-the-car balance.

    1. C144019
      Steel wheel

      Imbalance after adjustment:
      8.0 g (0.018 lb.) or less

      HINT:
      If necessary, check and adjust the on-the-car balance.

    2. C144018E02
      Others (Non-steel wheel)

      Imbalance after adjustment:
      8.0 g (0.018 lb.) or less

      NOTICE:
      1. Use a cleaning detergent to remove dirt, oil, and water from the surface where the balance weight attaches.
      2. Do not touch the adhesive surface of the tape.
      3. Attach the adhesive type balance weight to the flat position shown in the illustration.
      4. Push the balance weight securely with a finger to adhere it to the position.
      5. Do not reuse the balance weight.

      HINT:
      1. Inner side balance weight should be installed by clipping it to the rim.
      2. If necessary, check and adjust the on-the-car balance.


INSPECT FRONT AXLE HUB BEARING LOOSENESS

HINT:
(Click here)


INSPECT REAR AXLE HUB BEARING LOOSENESS

HINT:
(Click here)


INSPECT FRONT AXLE HUB RUNOUT

HINT:
(Click here)


INSPECT REAR AXLE HUB RUNOUT

HINT:
(Click here)

← INSPECTION (Jun 2006 – Sep 2006)INSPECTION (from Jun 2009) →