INSPECTION
Inspection · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| INSPECT TIRES |
Check the tires for wear and proper inflation pressure.
- Cold tire inflation pressure:
for Australia: Tire size
Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
215/60R16 95V
4 passengers or less
for 2AZ-FE
230 (2.3, 33)*1, 230 (2.3, 33)*2
210 (2.1, 31)*1, 230 (2.3, 33)*2
for 2GR-FE
210 (2.1, 31)*1, 230 (2.3, 33)*2
210 (2.1, 31)*1, 230 (2.3, 33)*2
5 passengers
240 (2.4, 35)*1, 300 (3.1, 44)*2
240 (2.4, 35)*1, 300 (3.1, 44)*2
215/55R17 93V
4 passengers or less
220 (2.2, 32)*1, 250 (2.5, 36)*2
220 (2.2, 32)*1, 250 (2.5, 36)*2
5 passengers
240 (2.4, 35)*1, 300 (3.1, 44)*2
240 (2.4, 35)*1, 300 (3.1, 44)*2
*2: For driving at over 140 km/h (87 mph)- Cold tire inflation pressure:
for GCC: Tire size
Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
215/60R16 95V
210 (2.1, 31)*1, 240 (2.4, 35)*2
210 (2.1, 31)*1, 240 (2.4, 35)*2
215/55R17 93V
220 (2.2, 32)*1, 240 (2.4, 35)*2
220 (2.2, 32)*1, 240 (2.4, 35)*2
*2: For driving at over 160 km/h (100 mph)
Using a dial indicator, check the runout of the tires.

- Tire runout:
- 1.4 mm (0.055 in.) or less
| ROTATE TIRES |
If the spare tire uses a different type of wheel from the other tires, rotate the tires as shown by (A) in the illustration. If the spare tire has the same type of wheel as the other tires, rotate the tires, including the spare tire, as shown by (B) in the illustration.

| INSPECT WHEEL BALANCE |
Check and adjust the off-the-car balance.
Steel wheel

- Imbalance after adjustment:
- 8.0 g (0.018 lb) or less
- HINT:
- If necessary, check and adjust the on-the-car balance.
Others (Non-steel wheel)

- Imbalance after adjustment:
- 8.0 g (0.018 lb) or less
- NOTICE:
- Use a cleaning detergent to remove dirt, oil, and water from the surface where the balance weight attaches.
- Do not touch the adhesive surface of the tape.
- Attach the adhesive type balance weight to the flat surface shown in the illustration.
- Push the balance weight securely with a finger to adhere it to the position.
- Do not reuse the balance weight.
- Use a cleaning detergent to remove dirt, oil, and water from the surface where the balance weight attaches.
- HINT:
- Inner side balance weight should be installed by clipping it to the rim.
- If necessary, check and adjust the on-the-car balance.
- Inner side balance weight should be installed by clipping it to the rim.
| INSPECT FRONT AXLE HUB BEARING LOOSENESS |
- HINT:
- (Click here)
| INSPECT REAR AXLE HUB BEARING LOOSENESS |
- HINT:
- (Click here)
| INSPECT FRONT AXLE HUB RUNOUT |
- HINT:
- (Click here)
| INSPECT REAR AXLE HUB RUNOUT |
- HINT:
- (Click here)
