2006-2011 Camry Aurion · Service Manual ENGINE

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built Jun 2006 – May 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using the intelligent tester.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1-trip detection logic):
(a) Turn the ignition switch to the ON position
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. STOP fuse
  4. IGN fuse
  5. ECM

WIRING DIAGRAM

A142855E02

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. STP signal conditions can be checked using the intelligent tester.
    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch to the ON position and turn the tester on.
    3. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.
    4. Check the STP signal when the brake pedal is depressed and released.
      Brake Pedal Operation
      Specified Condition
      Depressed
      STP signal ON
      Released
      STP signal OFF


1. CHECK STOP LIGHT SWITCH (TERMINAL VOLTAGE)

  1. A056986E09
    Disconnect the A19 stop light switch connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    B (A19-2) - Body ground
    9 to 14 V
    B (A19-3) - Body ground
    9 to 14 V

  1. Reconnect the stop light switch connector.



NG
Go to step 4
OK


2. INSPECT STOP LIGHT SWITCH

  1. A115657E05
    Disconnect the A19 stop light switch connector.

  1. Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω

  1. Reinstall the stop light switch.

  1. Reconnect the stop light switch connector.



NG
REPLACE STOP LIGHT SWITCH
OK


3. CHECK ECM (STP AND ST1 - VOLTAGE)

  1. A112585E07
    Disconnect the A24 ECM connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Brake Pedal Operation
    Specified Condition
    ST1- (A24-35) - Body ground
    Released
    9 to 14 V
    Depressed
    Below 1.5 V
    STP (A24-36) - Body ground
    Released
    Below 1.5 V
    Depressed
    9 to 14 V

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

4. INSPECT FUSE (STOP AND IGN FUSES)

  1. A132290E02
    Remove the STOP and IGN fuses from the instrument panel J/B.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the STOP and IGN fuses.



NG
REPLACE FUSE (STOP AND/OR IGN FUSES)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH)


← P0500 Vehicle Speed Sensor "A" (from Jun 2009)P0504 Brake Switch "A" / "B" Correlation (from Jun 2009) →