P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – May 2009 from Jun 2009
DESCRIPTION
The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.- HINT:
- The normal conditions are as shown in the table below. The signals can be read using the intelligent tester.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0504 |
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1-trip detection logic): (a) Turn the ignition switch on (IG) (b) Brake pedal released (c) STP signal OFF when ST1- signal OFF |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- STP signal conditions can be checked using the intelligent tester.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch on (IG) and turn the tester on.
- Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.
- Check the STP signal when the brake pedal is depressed and released.
Brake Pedal Operation
Specified Condition
Depressed
STP signal ON
Released
STP signal OFF
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK STOP LIGHT SWITCH (TERMINAL VOLTAGE) |
Disconnect the A79 stop light switch connector.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
B (A79-2) - Body ground
Always
9 to 14 V
B (A79-4) - Body ground
Ignition switch on (IG)
9 to 14 V
Reconnect the stop light switch connector.
|
|
||||
| OK | |
| 2. INSPECT STOP LIGHT SWITCH |
Disconnect the A79 stop light switch connector.

Remove the stop light switch.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Position
Specified Condition
1 - 2
Switch pin not pushed
Below 1 Ω
Switch pin pushed
10 kΩ or higher
3 - 4
Switch pin not pushed
10 kΩ or higher
Switch pin pushed
Below 1 Ω
Reinstall the stop light switch.
Reconnect the stop light switch connector.
|
|
||||
| OK | |
| 3. CHECK ECM (STP AND ST1- VOLTAGE) |
Disconnect the A24 ECM connector.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Brake Pedal Operation
Specified Condition
ST1- (A24-35) - Body ground
Released
7.5 to 14 V
Depressed
Below 1.5 V
STP (A24-36) - Body ground
Released
Below 1.5 V
Depressed
7.5 to 14 V
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 4. INSPECT FUSE (STOP AND IGN FUSES) |
Remove the STOP and IGN fuses from the instrument panel J/B.

Measure the resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the STOP and IGN fuses.
|
|
||||
| OK | ||
| ||
