2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the engine switch, any other switches, or a door triggers related ECU and sensor communication on the CAN.
This communication will cause the resistance value to change.

NOTICE:
This section describes the standard CAN values for all CAN related components.


JUNCTION CONNECTOR FOR CAN NO. 1 BUS

  1. CAN No. 1 J/C
    C152831E01

    CAN No. 1 J/C Connector ("A" side, with earth terminal)
    Connector Color
    Color (CAN-H Side)
    Color (CAN-L Side)
    CAN No. 1 Bus Main Wire (E42)
    White
    B
    W
    Center Airbag Sensor Assembly (E45)
    Black
    B
    W
    CAN No. 1 J/C Connector ("B" side, without earth terminal)
    Connector Color
    Color (CAN-H Side)
    Color (CAN-L Side)
    Yaw Rate Sensor (E46)
    Blue
    B
    W
    DLC3 (E62)
    White
    B
    W
    Steering Angle Sensor (E63)
    Brown
    B
    W
    Combination Meter (E43)
    White
    B
    W
    Main Body ECU (E44)
    Black
    B
    W

  2. CAN No. 4 J/C (REAR OF THE VEHICLE)
    C137762E08

    Wiring color: 
    Terminal
    Wiring Color
    Destination
    A40-1 (CANH)
    B
    ECM (CANH)
    A40-7 (CANL)
    W
    ECM (CANL)
    A40-2 (CANH)
    B
    Skid Control ECU (CANH)
    A40-8 (CANL)
    W
    Skid Control ECU (CANL)

  3. CAN No. 4 J/C (FRONT OF THE VEHICLE)
    C137763E30

    Wiring color: 
    Terminal
    Wiring Color
    Destination
    E41-1 (CANH)
    B
    A/C Amplifier (CANH)
    E41-7 (CANL)
    W
    A/C Amplifier (CANL)
    E41-4 (CANH)
    B
    CAN No. 1 J/C (CANH)
    E41-10 (CANL)
    W
    CAN No. 1 J/C (CANL)

  4. The connection diagram of the components which are connected to the CAN J/C
    C152826E01


JUNCTION CONNECTOR FOR CAN MS BUS

  1. CAN No. 3 J/C
    C142735E01

    Wiring color: 
    CAN No. 3 J/C Connector ("A" side, with earth terminal)
    Connector Color
    Color (CAN-H Side)
    Color (CAN-L Side)
    Certification ECU (O34)
    Gray
    L
    W
    Clearance Warning ECU (O32)
    Blue
    L
    W
    CAN MS Bus Main Wire (O33)
    White
    L
    W


DLC3

  1. C125062E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E10-6 (CANH) - E10-14 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E10-6 (CANH) - E10-4 (CG)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E10-6 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher


SKID CONTROL ECU WITH ACTUATOR

  1. C136493E11
    Disconnect the connector from the skid control ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    A26-35 (CANH) - A26-14 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    A26-35 (CANH) - A26-4 (GND1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    A26-14 (CANL) - A26-4 (GND1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    A26-35 (CANH) - A26-3 (+BS)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher
    A26-14 (CANL) - A26-3 (+BS)
    W - L
    LOW-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher


STEERING ANGLE SENSOR

  1. G026357E15
    Disconnect the connector from the steering angle sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E17-10 (CANH) - E17-9 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E17-10 (CANH) - E17-2 (ESS)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E17-9 (CANL) - E17-2 (ESS)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E17-10 (CANH) - E17-3 (BAT)
    B - W
    HIGH-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher
    E17-9 (CANL) - E17-3 (BAT)
    W - W
    LOW-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher


YAW RATE SENSOR

  1. C225737E01
    Disconnect the connector from the yaw rate sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E34-2 (CANH) - E34-3 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E34-2 (CANH) - E34-4 (GND)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E34-3 (CANL) - E34-4 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E34-2 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher
    E34-3 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher


CENTER AIRBAG SENSOR

  1. C125063E03
    Disconnect the connector from the center airbag sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E30-13 (CANH) - E30-22 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E30-13 (CANH) - E30-25 (E1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E30-22 (CANL) - E30-25 (E1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E30-13 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher
    E30-22 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher


ECM

  1. Disconnect the connector from the ECM.
    A107881E78

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Value
    A55-41 (CANH) - A55-49 (CANL)
    Engine switch off
    108 to 132 Ω

  3. C136709E17
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    A55-41 (CANH) - A55-49 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    108 to 132 Ω
    A55-41 (CANH) - C55-81 (E1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    A55-49 (CANL) - C55-81 (E1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    A55-41 (CANH) - A55-20 (BATT)
    B - Y
    HIGH-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher
    A55-49 (CANL) - A55-20 (BATT)
    W - Y
    LOW-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER

  1. E124470E20
    Disconnect the connector from the air conditioning amplifier.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E38-11 (CANH) - E38-12 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E38-11 (CANH) - E38-14 (GND)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E38-12 (CANL) - E38-14 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E38-11 (CANH) - E38-21 (B)
    B - GR
    HIGH-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher
    E38-12 (CANL) - E38-21 (B)
    W - GR
    LOW-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher


COMBINATION METER

  1. C133254E01
    Disconnect the connector from the combination meter.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Value
    F1-17 (CANH) - F1-18 (CANL)
    Engine switch off
    108 to 132 Ω

  3. C133255E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    F1-17 (CANH) - F1-18 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    108 to 132 Ω
    F1-17 (CANH) - F1-12 (E2)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    F1-18 (CANL) - F1-12 (E2)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    F1-17 (CANH) - F1-2 (B2)
    B - R
    HIGH-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher
    F1-18 (CANL) - F1-2 (B2)
    W - R
    LOW-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher


CERTIFICATION ECU

  1. C142197E02
    Disconnect the connector from the certification ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Value
    E58-27 (CANH) - E58-28 (CANL)
    Engine switch off
    108 to 132 Ω

  3. C142198E04
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E58-27 (CANH) - E58-28 (CANL)
    L - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    108 to 132 Ω
    E58-27 (CANH) - E58-17 (E)
    L - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E58-28 (CANL) - E58-17 (E)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E58-27 (CANH) - E58-1 (+B)
    L - W
    HIGH-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher
    E58-28 (CANL) - E58-1 (+B)
    W - W
    LOW-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher


MAIN BODY ECU (INSTRUMENT PANEL J/B)

  1. C144955E02
    Disconnect the connector from the main body ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Value
    E8-16 (CANP) - E8-15 (CANN)
    Engine switch off
    108 to 132 Ω

  3. Measure the resistance according to the value(s) in the table below.
    C142736E01


Standard resistance:
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E8-5 (CANH) - E8-6 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E8-5 (CANH) - E10-4 (CG)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-6 (CANL) - E10-4 (CG)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-5 (CANH) - E10-16 (BAT)
B - L
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E8-6 (CANL) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E8-16 (CANP) - E8-15 (CANN)
L - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
E8-16 (CANP) - E10-4 (CG)
L - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-15 (CANN) - E10-4 (CG)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-16 (CANP) - E10-16 (BAT)
L - L
HIGH-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher
E8-15 (CANN) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Engine switch off
6 kΩ or higher


CLEARANCE WARNING ECU

  1. C142212E03
    Disconnect the connector from the clearance warning ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    O30-3 (R1) - O30-5 (R2)
    L - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    O30-3 (R1) - O30-17 (E)
    L - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    O30-5 (R2) - O30-17 (E)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    O30-3 (R1) - E10-16 (BAT)
    L - L
    HIGH-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher
    O30-5 (R2) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Engine switch off
    6 kΩ or higher

← PROBLEM SYMPTOMS TABLE (from Jun 2009)TERMINALS OF ECU (from Jun 2009) →