2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the engine switch, any other switches, or a door triggers related ECU and sensor communication on the CAN.
This communication will cause the resistance value to change.

NOTICE:
This section describes the standard CAN values for all CAN related components.


JUNCTION CONNECTOR FOR CAN NO. 1 BUS

  1. CAN No. 1 J/C
    C142744E05

    CAN No. 1 J/C Connector ("A" side, with earth terminal)
    Connector Color
    Color (CAN-H Side)
    Color (CAN-L Side)
    CAN No. 1 Bus Main Wire (E42)
    White
    B
    W
    Center Airbag Sensor Assembly (E45)
    Black
    B
    W
    CAN No. 1 J/C Connector ("B" side, without earth terminal)
    Connector Color
    Color (CAN-H Side)
    Color (CAN-L Side)
    Yaw Rate Sensor (E46)
    Blue
    B
    W
    Air Conditioning Amplifier (E47)
    Gray
    B
    W
    Navigation Receiver Assembly (E93)
    Brown
    B
    W
    Combination Meter (E43)
    White
    B
    W
    Main Body ECU (E44)
    Black
    B
    W

  2. CAN No. 4 J/C (REAR OF THE VEHICLE)
    C137762E19

    Wiring color: 
    Terminal
    Wiring Color
    Destination
    A40-1 (CANH)
    B
    ECM (CANH)
    A40-7 (CANL)
    W
    ECM (CANL)
    A40-2 (CANH)
    B
    Skid Control ECU (CANH)
    A40-8 (CANL)
    W
    Skid Control ECU (CANL)

  3. CAN No. 4 J/C (FRONT OF THE VEHICLE)
    C137763E28

    Wiring color: 
    Terminals
    Wiring Color
    Destination
    E41-1 (CANH)
    B
    Gateway ECU (CANH) *
    E41-7 (CANL)
    W
    Gateway ECU (CANL) *
    E41-2 (CANH)
    B
    DLC3 (CANH)
    E41-8 (CANL)
    W
    DLC3 (CANL)
    E41-3 (CANH)
    B
    Steering Angle Sensor (CANH)
    E41-9 (CANL)
    W
    Steering Angle Sensor (CANL)
    E41-4 (CANH)
    B
    CAN No. 1 J/C (CANH)
    E41-10 (CANL)
    W
    CAN No. 1 J/C (CANL)
    *: with AFS

  4. The connection diagram of the components which are connected to the CAN J/C
    C212319E01


JUNCTION CONNECTOR FOR CAN MS BUS

  1. CAN No. 3 J/C
    C142735E02

    Wiring color: 
    CAN No. 3 J/C Connector ("A" side, with earth terminal)
    Connector Color
    Color (CAN-H Side)
    Color (CAN-L Side)
    Certification ECU (O34)
    Gray
    L
    W
    Clearance Warning ECU (O32)
    Blue
    L
    W
    CAN MS Bus Main Wire (O33)
    White
    L
    W

  2. CAN No. 5 J/C (w/ Seat Position Memory)
    C142785E10

    Wiring color: 
    Terminal
    Wiring color
    Destination
    E81-11 (CANH)
    L
    Main Body ECU (CANP)
    E81-22 (CANL)
    W
    Main Body ECU (CANN)
    E81-9 (CANH)
    L
    Seat Position Control ECU (CANH)
    E81-20 (CANL)
    W
    Seat Position Control ECU (CANL)
    E81-8 (CANH)
    L
    Outer Mirror Control ECU (CAN)
    E81-19 (CANL)
    W
    Outer Mirror Control ECU (CGND)
    E81-10 (CANH)
    L
    CAN No. 3 J/C (CANH)
    E81-21 (CANL)
    W
    CAN No. 3 J/C (CANL)

  3. CAN No. 6J/C (w/ TOYOTA Link System)
    C188960E07

    Wiring color: 
    Terminal
    Wiring color
    Destination
    N40-1 (CANH)
    L
    Main Body ECU (CANP)
    N40-6 (CANL)
    W
    Main Body ECU (CANN)
    N40-2 (CANH)
    L
    CAN No. 5 J/C (CANH)
    N40-7 (CANL)
    W
    CAN No. 5 J/C (CANL)
    N40-3 (CANH)
    L
    Mayday ECU (MPX1)
    N40-8 (CANL)
    W
    Mayday ECU (MPX2)


JUNCTION CONNECTOR FOR CAN NO. 2 BUS (w/ AFS)

  1. CAN No. 2 J/C
    C142300E07

    Wiring color: 
    CAN No. 2 J/C Connector ("A" Side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    CAN No. 2 Bus Main Wire (E79)
    White
    R
    W
    AFS ECU (E80)
    Black
    R
    W


DLC3

  1. C125062E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E10-6 (CANH) - E10-14 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E10-6 (CANH) - E10-4 (CG)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E10-6 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


SKID CONTROL ECU WITH ACTUATOR

  1. C136493E11
    Disconnect the connector from the skid control ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    A26-35 (CANH) - A26-14 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    A26-35 (CANH) - A26-4 (GND1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    A26-14 (CANL) - A26-4 (GND1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    A26-35 (CANH) - A26-3 (+BS)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A26-14 (CANL) - A26-3 (+BS)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


STEERING ANGLE SENSOR

  1. G026357E15
    Disconnect the connector from the steering angle sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E17-10 (CANH) - E17-9 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E17-10 (CANH) - E17-2 (ESS)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E17-9 (CANL) - E17-2 (ESS)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E17-10 (CANH) - E17-3 (BAT)
    B - W
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E17-9 (CANL) - E17-3 (BAT)
    W - W
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


YAW RATE SENSOR

  1. C225737E01
    Disconnect the connector from the yaw rate sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E34-2 (CANH) - E34-3 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E34-2 (CANH) - E34-4 (GND)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E34-3 (CANL) - E34-4 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E34-2 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E34-3 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


CENTER AIRBAG SENSOR

  1. C125063E09
    Disconnect the connector from the center airbag sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E30-13 (CANH) - E30-22 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E30-13 (CANH) - E30-25 (E1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E30-22 (CANL) - E30-25 (E1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E30-13 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E30-22 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


ECM

  1. Disconnect the connector from the ECM.
    A107881E77

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Value
    A24-41 (CANH) - A24-49 (CANL)
    Engine switch off
    108 to 132 Ω

  3. C136709E19
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    A24-41 (CANH) - A24-49 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    108 to 132 Ω
    A24-41 (CANH) - C58-81 (E1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    A24-49 (CANL) - C58-81 (E1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    A24-41 (CANH) - A24-20 (BATT)
    B - Y
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A24-49 (CANL) - A24-20 (BATT)
    W - Y
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER

  1. E124470E20
    Disconnect the connector from the air conditioning amplifier.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E38-11 (CANH) - E38-12 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E38-11 (CANH) - E38-14 (GND)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E38-12 (CANL) - E38-14 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E38-11 (CANH) - E38-21 (B)
    B - GR
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E38-12 (CANL) - E38-21 (B)
    W - GR
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


COMBINATION METER (for 2AZ-FE Engine)

  1. C133254E06
    Disconnect the connector from the combination meter.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Value
    F1-23 (CANH) - F1-22 (CANL)
    Engine switch off
    108 to 132 Ω

  3. C133255E07
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    F1-23 (CANH) - F1-22 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    108 to 132 Ω
    F1-23 (CANH) - F1-12 (E2)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    F1-22 (CANL) - F1-12 (E2)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    F1-23 (CANH) - F1-2 (B2)
    B - R
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    F1-22 (CANL) - F1-2 (B2)
    W - R
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


COMBINATION METER (for 2GR-FE Engine)

  1. C133254E01
    Disconnect the connector from the combination meter.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Value
    F1-17 (CANH) - F1-18 (CANL)
    Engine switch off
    108 to 132 Ω

  3. C133255E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    F1-17 (CANH) - F1-18 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    108 to 132 Ω
    F1-17 (CANH) - F1-12 (E2)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    F1-18 (CANL) - F1-12 (E2)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    F1-17 (CANH) - F1-2 (B2)
    B - R
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    F1-18 (CANL) - F1-2 (B2)
    W - R
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)
E134716E13

  1. C210950E03
    Disconnect the navigation receiver assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F12-2 (CANH) - F12-3 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine Switch off
    108 to 132 Ω
    F12-2 (CANH) - F36-7 (GND)
    B - BR
    HIGH-level CAN bus wire - Ground
    Engine Switch off
    200 Ω or higher
    F12-3 (CANL) - F36-7 (GND)
    W - BR
    LOW-level CAN bus wire - Ground
    Engine Switch off
    200 Ω or higher
    F12-2 (CANH) - F36-4 (B)
    B - L-Y
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    F12-3 (CANL) - F36-4 (B)
    W - L-Y
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


MAIN BODY ECU (INSTRUMENT PANEL J/B)

  1. C144955E02
    Disconnect the connector from the main body ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Value
    E8-16 (CANP) - E8-15 (CANN)
    Engine switch off
    108 to 132 Ω

  3. Measure the resistance according to the value(s) in the table below.
    C142736E01


Standard resistance:
CAN No. 1 Bus Branch Wire 
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E8-5 (CANH) - E8-6 (CANL)
B - W
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
54 to 69 Ω
E8-5 (CANH) - E10-4 (CG)
B - W-B
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-6 (CANL) - E10-4 (CG)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-5 (CANH) - E10-16 (BAT)
B - L
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E8-6 (CANL) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
CAN MS Bus Main Wire 
Terminals
Wiring Color
Terminal Description
Condition
Specified Value
E8-16 (CANP) - E8-15 (CANN)
L - W (*1)
B -W (*2)
HIGH-level CAN bus wire - LOW-level CAN bus wire
Engine switch off
108 to 132 Ω
E8-16 (CANP) - E10-4 (CG)
L - W-B (*1)
B - W-B (*2)
HIGH-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-15 (CANN) - E10-4 (CG)
W - W-B
LOW-level CAN bus wire - Ground
Engine switch off
200 Ω or higher
E8-16 (CANP) - E10-16 (BAT)
L - L (*1)
B - L (*2)
HIGH-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E8-15 (CANN) - E10-16 (BAT)
W - L
LOW-level CAN bus wire - Battery positive
Cable disconnected from negative (-) battery terminal
6 kΩ or higher

*1: for 2GR-FE Engine
*2: for 2AZ-FE Engine

CERTIFICATION ECU

  1. C142197E02
    Disconnect the connector from the certification ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Value
    E58-27 (CANH) - E58-28 (CANL)
    Engine switch off
    108 to 132 Ω

  3. C142198E04
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E58-27 (CANH) - E58-28 (CANL)
    L - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    108 to 132 Ω
    E58-27 (CANH) - E58-17 (E)
    L - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E58-28 (CANL) - E58-17 (E)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E58-27 (CANH) - E58-1 (+B)
    L - W
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E58-28 (CANL) - E58-1 (+B)
    W - W
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


CLEARANCE WARNING ECU (w/ Parking Assist-sensor System)

  1. C142212E02
    Disconnect the connector from the clearance warning ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    O30-3 (R1) - O30-5 (R2)
    L - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    O30-3 (R1) - O30-17 (E)
    L - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    O30-5 (R2) - O30-17 (E)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    O30-3 (R1) - E10-16 (BAT)
    L - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    O30-5 (R2) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


OUTER MIRROR CONTROL ECU (w/ Seat Position Memory)

  1. C142227E06
    Disconnect the connector from the outer mirror control ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E85-1 (CAN) - E85-21 (CGND)
    L - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E85-1 (CAN) - E86-9 (GND)
    L - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E85-21 (CGND) - E86-9 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E85-1 (CAN) - E86-3 (B)
    L - W-R
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E85-21 (CGND) - E86-3 (B)
    W - W-R
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


SEAT POSITION CONTROL ECU (Front RH Side) (w/ Seat Position Memory)

  1. B128716E17
    Disconnect the connector from the seat position control ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    T21-5 (CANH) - T21-1 (CANL)
    L - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    T21-5 (CANH) - T20-1 (GND)
    L - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    T21-1 (CANL) - T20-1 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    T21-5 (CANH) - T20-5 (+B)
    L - G
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    T21-1 (CANL) - T20-5 (+B)
    W - G
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


MAYDAY ECU (w/ TOYOTA Link System)

  1. B169476E02
    Disconnect the connector from the seat position control ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    N46-2 (MPX1) - N46-1 (MPX2)
    L - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    N46-2 (MPX1) - N46-4 (GND)
    L - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    N46-1 (MPX2) - N46-4 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    N46-2 (MPX1) - N46-3 (B+)
    L - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    N46-1 (MPX2) - N46-3 (B+)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


GATEWAY ECU (w/ AFS)

  1. Disconnect the connector from the gateway ECU.
    C142189E03

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Value
    E70-13 (CA2H) - E70-12 (CA2L)
    Engine switch off
    108 to 132 Ω

  3. C142190E05
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    CAN No. 1 Bus Branch Wire 
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E70-16 (CA1H) - E70-15 (CA1L)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    E70-16 (CA1H) - E70-4 (GND)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E70-15 (CA1L) - E70-4 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E70-16 (CA1H) - E70-2 (BATT)
    B - W
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E70-15 (CA1L) - E70-2 (BATT)
    W - W
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    CAN No. 2 Bus Main Wire 
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E70-13 (CA2H) - E70-12 (CA2L)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    108 to 132 Ω
    E70-13 (CA2H) - E70-4 (GND)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E70-12 (CA2L) - E70-4 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    E70-13 (CA2H) - E70-2 (BATT)
    B - W
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher
    E70-12 (CA2L) - E70-2 (BATT)
    W - W
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher


AFS ECU (w/ AFS)

  1. C142217E03
    Disconnect the connector from the AFS ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    A61-12 (MPX1) - A61-13 (MPX2)
    R - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Engine switch off
    54 to 69 Ω
    A61-12 (MPX1) - A61-22 (EIS)
    R - W
    HIGH-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    A61-13 (MPX2) - A61-22 (EIS)
    W - W
    LOW-level CAN bus wire - Ground
    Engine switch off
    200 Ω or higher
    A61-12 (MPX1) - E10-16 (BAT)
    R - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A61-13 (MPX2) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

← TERMINALS OF ECU (Oct 2006 – May 2009)DIAGNOSIS SYSTEM (Oct 2006 – May 2009) →