2006-2011 Camry Aurion · Service Manual STEERING

Steering Lock Motor Drive Power Circuit

Circuit diagnosis · Vehicles built from Oct 2006

DESCRIPTION

The steering lock ECU is connected to the main body ECU and certification ECU. The steering lock ECU cannot activate the motor unless it receives permission signals from both ECUs. (The main body ECU permits the steering lock ECU to supply power to activate the motor.)

WIRING DIAGRAM

C113485E03

INSPECTION PROCEDURE


1. CHECK VEHICLE CONDITION
  1. Check the problem symptom of the steering lock system.

    Result:
    Condition
    Proceed to
    Steering lock cannot be released
    A
    Steering cannot be locked
    B



B
Go to step 6
A


2. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG), and turn the intelligent tester on.

  1. Select the item below in the DATA LIST, and read its value displayed on the intelligent tester.

    Entry & Start: 
    Item
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    LCK/UNLCK REC
    Steering lock command reception record / YES or NO
    YES: Steering lock/unlock signal received
    NO: Steering lock/unlock signal not received
    -

  1. Check if a steering unlock command signal has been received.

    OK:
    "YES" is displayed on the tester display.



NG
CHECK SMART ENTRY AND START SYSTEM
OK


3. INSPECT STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

  1. C106483E22
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E51-3 (IGE) - E51-1 (GND)
    1. Engine switch off
    2. Engine switch on (ACC or IG)
    1. Motor activated: Below 1 V
    2. Motor not activated:
      10 to 12 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


4. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - BODY GROUND)

  1. C106484E28
    Disconnect the E51 connector from the steering lock actuator assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E51-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - MAIN BODY ECU)

  1. C113502E01
    Disconnect the E7 connector from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E51-3 (IGE) - E7-19 (SLR+)
    Always
    Below 1 Ω
    E51-3 (IGE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

6. INSPECT STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

  1. C106483E22
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E51-3 (IGE) - E51-1 (GND)
    The specified condition should be checked after performing the following:
    1. Move the shift lever to the P position
    2. Turn the engine switch off
    3. Open the driver's door
    1. Motor activated: Below 1 V
    2. Motor not activated:
      10 to 12 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


7. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - MAIN BODY ECU)

  1. C113502E01
    Disconnect the E51 connector from the steering lock actuator assembly.

  1. Disconnect the E7 connector from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E51-3 (IGE) - E7-19 (SLR+)
    Always
    Below 1 Ω
    E51-3 (IGE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← B2788 IG2 Signal Malfunction (from Oct 2006)Unlock Position Sensor Signal Circuit (from Oct 2006) →