2006-2011 Camry Aurion · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL ENGINE REAR OIL SEAL
  1. Apply MP grease to a new oil seal lip.

    NOTICE:
    Keep the lip free from foreign matter.

  1. A128874E01
    Using SST and a hammer, tap in the oil seal until its surface is flush with the rear oil seal retainer edge.
    SST
    09223-15030  
    09950-70010   (09951-07100)

    NOTICE:
    Wipe off extra grease from the crankshaft.


2. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

  1. A126932E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Clean the bolt and the bolt hole.

  1. Apply adhesive to 2 or 3 threads of the bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A060816
    Install the flywheel with the 8 bolts. Uniformly tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    130 N*m{ 1,330 kgf*cm , 96 ft.*lbf }


3. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

  1. C127508E01
    Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.
    SST
    09301-00220  

    NOTICE:
    Take care not to insert the clutch disc assembly in the wrong direction.


4. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

  1. C127509E02
    Align the matchmarks on the clutch cover assembly with the one on the flywheel sub-assembly.

  1. Following the procedures shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin on the top.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Following the order in the illustration, evenly tighten the bolts one turn at a time.
    2. Lightly move SST up and down, and right and left after checking that the disc is in the center to tighten the bolts.

    SST
    09301-00210  


5. INSTALL DRIVE PLATE & RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)

  1. A126932E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Clean the bolt and the bolt hole.

  1. Apply adhesive to 2 or 3 threads of the bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A112224E01
    Install the front spacer, drive plate and rear spacer with the 8 bolts. Uniformly tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }


6. INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

HINT:
Click here.


7. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)

HINT:
Click here.

← REMOVAL (from Jun 2009)INSTALLATION (Oct 2006 – May 2009) →